For those of you with APCC Standard and "Check for updates" is not working, please try this version: http://www.apastrosoftware.com/apcc_download/APCC_Standard_Setup_1.8.8.14.exe If you still get a "b

Have you found multistar to be better? I tried it and didn't see any improvement. My guiding has been poor for months then GREAT for months then back to poor since I got the Mach1 I've solved my other

Hi Ray, Now it's working !!! :-) Regards, Yves Le 15/01/21 11:17, Ray Gralak <groups3@...> a écrit : For those of you with APCC Pro and "Check for updates" is not working, please try this version (I'l

Hello recently sold my 1100 and kept the 8” portable pier. But I’m wanting to use it for my Mach2. Was looking for a adapter but couldn’t find one on your website. Am I missing it, or is this not poss

The Active X service in W10 is running (did both Manual and Auto settings) still no joy! I have three W10 machines and they all report the same problem when trying to plate solve. Anyone have an idea?

In the winter, I often observe in below freezing temperatures. So my 1st battery was one from Kendrick where I could use 15v instead of 12v. 15v was recommended in the AP 1100 manual. I am looking at

Hello, 1- For the last few months, my APCC pro no longer checks nor able to detect updates. Please see attached screen shot. 2- I have been downloading updates manually from AP website. However, the v

I recently upgraded from a CP3 to a CP4 for my Mach1. I have found conflicting information in AP documentation regarding whether I can reuse the existing PEMPro PEC curve created with the CP3. On page

Just a reminder for those who are waiting for Mach1 mounts and have Renishaw low temp encoders ordered, the delivery of the encoders has been affected by Covid shutdown. We are anticipating delivery s

I seem to have some errors when I have my stuff out in the cold. This is california cold at 47F. Every frame I downloaded had this weird mosaic tile puzzle look to it. Qhy says it is USB CrC errors. S

I have a usually reliable AP1600 mount. It is slewing fine but autoguiding suddenly went wild a little while ago. So normally I get very small guide errors .2 to .6 arc sec guide errors. They suddenly

This is a recurring problem that I’ve often blamed on ACP but am rethinking this as the screen shot shows ACP attempting to park, the ASCOM driver says it’s parking, and APCC says it is parked. I’m gu

How far away is APPC 1.9 from being released? (With ASTAP Plate Solving support)? No specifics needed, just like in: Weeks, months, quarters or years? I'd like to run an APPM at some point, and just w

Used the QHY Polemax camera and software to dial in the polar alignment which seemed pretty straight forward. Should be right on the money. Then I also happen to have the MGbox and that is connected p

I would like to use the new Eagle 4 with my Mach 2's thru mount cabling. I will be using all AC power, so I have the Eagle's AC power adapter. I have Primaluce's Eagle power connector with the Anderso

Hi, I am just wanting to confirm that I am entering the information into the keypad correctly. Longitude: 30.2317568 Latitude: -81.395712 My Keypad Entry N 30:13:54.3 W 081:23:44.6 Thanks

Hi, I am doing table-top testing of our Mach2 (before we can put it on a proper tripod). I use TheSky6 in a Windows 7 virtual machine on my Mac. GTOCPS5 is connected to the computer with a short USB2.

On 12/30/2020 10:23 PM, deonb wrote: >Windows 7 on parallels. By now > it's an 11 year old operating system that got obsoleted 8 years ago, and > stopped getting security updates a year ago. > As a de

All, I am trying to connect a U-Blox7 GPS to v1.8.8.0 of APCC and I get this error message: UpdateLocation. Index and length must refer to a location within the string. Parameter name: Length. The gps

While reading a post by a fellow AP’er I saw a discussion about a product called Dragonfly and was instantly intrigued about what I was reading and it’s capabilities. Having had a few mishaps with my