Thanks for the confirmation Roberto. I was assuming that would be the case but thought I'd check with someone who has more experience with it. My setup is quite compact and I've done as much as I can

I was looking for user experience on the 10x60 Baader guide scope with Astro-Physics guider bracket and wondered if there is any potential need for special balancing when it is side mounted to the tel

Hi Dale, Yes, with Ray's help it looks like things are sorted out and running as expected again. Thanks for posting your MF settings. Mine matched except for the use of "Use telescope side of pier" wh

#APCC

Ray, Deleting the settings file did the trick! The mount seems to be connecting and pointing fine now. Thanks, Joe

"Reinstalling APCC is not likely going to help unless APCC had become corrupted through some disk error on your computer. More likely is that the settings file has become corrupted. So, try deleting:

I posted the message below initially under the topic of "Smart Meridian Flip with NINA" but I'm starting a new thread on this topic because at this point it has nothing to do with the original problem

I'm hoping for some suggestions to help restore a functional connection between my computer and the mount. After the latest event that started with a meridian flip followed by pointing issues which th

#APCC

Hi Andrew, Thanks for the insight. I agree, the software has a lot of potential. My needs are definitely simpler than yours! Software that simplifies a number of routines the way the advanced sequence

#APCC

Thanks Ray. I definitely get the point for needing additional sample points on the west side. I'll give it another run and see how it goes. Joe

#APCC

Got it. Are there any particular parameters in the Meridian tab I should be cautious about? I've always kept the "Counterweight Up Slews within:" East and West limits boxes checked. When sitting nearb

#APCC

OK, thanks. I've actually starting making Dec models with three rows of points but I had this one already made so I used it. Ironically I looked at it just before starting the mapping and debated whet

#APCC

Hi Ray, Files are posted here: https://drive.google.com/file/d/1Bkzp6E7gyMqm1zBJdabUFEeax7unijmY/view?usp=sharing The model was created just before the imaging run. I didn't notice any problems during

#APCC

I've still got a problem with NINA and APCC. Last night I created a relatively simple a sequence in the advanced sequencer (one filter, 5 minute subs for 3.5 hours then park the scope) and all went we

#APCC

Looks great! Glad to see you've got it fixed and are ready to go. I got the CTU on my telescope and adjusted fairly well. Just like you I was surprised how little movement the camera needed to flatten

Not sure yet. I got APCC working again with CdC and NINA yesterday but haven't run another sequence yet due to overcast skies. The .mlm file I was using during the last sequencer run with the errant s

#APCC

I didn’t know that. That makes it all the easier for everyone. The improvements in the entire mount software package over the past four years have been amazing. Glad I was able to bring that part to y

#APCC

There may have been no problem with 3 and 4. I have been designating the higher numbers based on the APCC manual where they’re recommended.

#APCC

Ray, Thanks for the tip on auto-configuration of port selection, I've got it checked. I think I need to remember to power cycle the mount when I'm working on connections, correct? I'll admit the assig

#APCC

Logs are posted here: https://drive.google.com/file/d/1SNl8HLBI4f7ZwGcxsXUghMX8pPz4ArTF/view?usp=sharing Mount: Mach1GTO/CP4 APCC-Pro v1.9.0.11 ASCOM V2 driver 5.30.10 CP4 software P02-08 Friday, Oct.

#APCC

Ray, I'm connected to the mount by ethernet cable. I've had the computer disconnect from the mount a couple times when I've moved it without holding the cables but it's a simple fix of restarting. It

#APCC