Date   

Re: APCC Pro with Mach2?

Dominique Durand
 
Edited

Hi Rolando,

It rolls for me quite like that. On June 14 I threw a photo spoiled by the clouds and I did not realize it until after. Without guidance no worries for the following takes ... and tonight it turns without problems either with the mach2 and APCC -Pro ... only operations to do because I do not have the THUM probe, adjust the temperature on APCC. I would like to go directly to a temperature + pressure probe.

Dominique


Re: Mach1 problem please assist

Ron Kramer
 

Yep - one continuous run. Not near the meridian.  I'm attaching pics in email. It asks original, best fit etc.  Upon appearing it's a small little blurry version.
would it make them more clear if I enter the post in the groups interface and not in email?   These are BIG ANC CLEAR AND SHARP when I attach them.

I
shape.JPG
dental in shape when zooming in.


On Thu, Jun 18, 2020 at 5:11 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
The graph shows 7 RA motions in the down direction, then a number of RA moves in the opposite direction. Is this over a period of time continuously? In other words, was this graph taken without interruption?

Roland



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 3:42 pm
Subject: Re: [ap-gto] Mach1 problem please assist

Capture is CLEAR and sharp. not sure what "GROUPS" does to images. I hate GROUPS.  Forums are better and allow you to retain/library of topics and Q&A, = (
I'll attach it again.  Is there a limit? size? restriction?    I'll attach at ORIGINAL SIZE


RA KICK.JPG

On Thu, Jun 18, 2020 at 4:37 PM Ron Kramer <ronkramer1957@...> wrote:
I don't own use a keypad.   I did try that SWAP OVER - but I then cleaned it and not sure where it ended up.  Since the last test clearly had the saime  KICKS. I can do ig again.  
What does that do?  I think it might track toward the other side of the groove?  I'll swap it over again and see if it helps since re-greasing.

NICELY - greasing lowered my RA RMA error almost 50%.  Here is my history.

Mount arrived. I guided around 1.0.  Always trying to tweak it - not sure why but months later I was guiding at  .24 RMS error (arc set). yeah - that's awesome.
MANY months of that... The RASA guided better than my long APO.  But late winter I swapped RASA V1 for a RASA V2 (heavier) and ever since my guiding was 1.5 average.  My image scale is 1.69 
lately - the RA kicks put me into  1.7-2.0.  I get double stars on every other sub. 
I re-greased the RA and last night afterwards I was 1.1max and usuall around .89 tot rms arc sec. (nice)  But the RA still kicks and makes for double stars.  My dec was still poor so I'll regrease dec next and check
my alignment. (it's fairly perminent in a dome, but I have a tripod leg/mount and it "can move".  I usually check alignment 1-2 times a year or when ever guiding quality decreases. 
I am not aware of any gear scraping - I always release it clean...  I have on 3-4 occasions allowed it to track into a leg and (stop). Not sure if that hurts anything. But seems to work fine next time.

I don't understand why the RA kick changed from lower to higher (E to W?) the mount orientation did not change. 
I'll swap the part positions over and try again tonight.  During regreasing/cleaning I saw nothing strange. No chunks or crud.  old Grease moved quickly,  freely. not at all gummy. 
I have some pics n video.



On Thu, Jun 18, 2020 at 3:39 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Hello Ron,

Howard won't be able to answer you at this time.

Can you do a test for me?

With keypad in Autostart NO, send the mount to Park1 and turn off power.
Loosen the clutches and move the mount to Park5 manually.
Turn power back on and press "Resume from Park5"

Now check to see if the RA anomaly persists. let me know the results and we can go from there.

By the way, your screen shot is so blurry I cannot make out any details on it.

Rolando



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 1:35 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:
Ron,
 
Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.
 
Try regreasing first and contact us again if you can’t resolve the issue.
 
Clear Skies,
 
Marj Christen
Astro-Physics, Inc
11250 Forest Hills Rd
Machesney Park, IL 61115
Phone: 815-282-1513
Fax: 815-282-9847
 
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist
 
I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 
I ordered the grease, I'll see how that goes.
 
 
On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.
 
You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.
 
Rolando
 
 
 
-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist
My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  
Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately
the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.
Nothing I have tried to far has fixed it.
I will include the log from a couple nights ago to show what I mean. 
I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  
I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  
I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 
 
 

 
--


--


--


--


--




APCC Pro with Mach2?

Roland Christen
 

I would like to remind everyone that the Mach2 purchase price includes APCC Pro and all modeling routines and programs in the keypad also, if the keypad is purchased. There's an ongoing thread in CN that can be misleading.

You also get a hefty counterweight bar which by itself counterweighs a small scope setup. Yes, actual counterweights are extra as well as tripods, piers and dovetail plates.

If in doubt about prices, what's included and options, don't ask posters on other newsgroups, just visit our webpage.

By the way, with good polar alignment, I have tested our tracking model to be accurate for up to 1 hour exposures with my 160EDF refractor. I got a max drift of around 1 arc sec in that hour's time. What this means is that you can probably set up your imaging rig, eliminate all the extra claptrap needed for guiding (camera, guide scope, wires, guide software etc) and save a bit of money. Makes the setup much cleaner too. I imaged for many hours with super smooth tracking in RA and Dec, and had to throw out only an occasional sub due to passing clouds. The clouds did not affect the tracking one bit. If I had been guiding, it would have gone for parts unknown when the clouds passed over.

Rolando


Re: Mach1 problem please assist

Worsel
 

Ron

You could provide logs same as on the PHD2 forum...just provide the link to the PHD2 server.

Bryan


Re: Mach1 problem please assist

Roland Christen
 

That's interesting.
A gear defect can only occur every 6.4 minutes, never at some random time or at shorter or longer time periods. There was no answer as to what the time period was for each spike, and the graph time cannot be read. It woudl really be helpful to know the time period.

Rolando


-----Original Message-----
From: Brian Valente <bvalente@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 4:25 pm
Subject: Re: [ap-gto] Mach1 problem please assist

those big offsets and changing directions look an awful lot like the spiral dither pattern in PHD

On Thu, Jun 18, 2020 at 2:11 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
The graph shows 7 RA motions in the down direction, then a number of RA moves in the opposite direction. Is this over a period of time continuously? In other words, was this graph taken without interruption?

Roland



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 3:42 pm
Subject: Re: [ap-gto] Mach1 problem please assist

Capture is CLEAR and sharp. not sure what "GROUPS" does to images. I hate GROUPS.  Forums are better and allow you to retain/library of topics and Q&A, = (
I'll attach it again.  Is there a limit? size? restriction?    I'll attach at ORIGINAL SIZE


RA KICK.JPG

On Thu, Jun 18, 2020 at 4:37 PM Ron Kramer <ronkramer1957@...> wrote:
I don't own use a keypad.   I did try that SWAP OVER - but I then cleaned it and not sure where it ended up.  Since the last test clearly had the saime  KICKS. I can do ig again.  
What does that do?  I think it might track toward the other side of the groove?  I'll swap it over again and see if it helps since re-greasing.

NICELY - greasing lowered my RA RMA error almost 50%.  Here is my history.

Mount arrived. I guided around 1.0.  Always trying to tweak it - not sure why but months later I was guiding at  .24 RMS error (arc set). yeah - that's awesome.
MANY months of that... The RASA guided better than my long APO.  But late winter I swapped RASA V1 for a RASA V2 (heavier) and ever since my guiding was 1.5 average.  My image scale is 1.69 
lately - the RA kicks put me into  1.7-2.0.  I get double stars on every other sub. 
I re-greased the RA and last night afterwards I was 1.1max and usuall around .89 tot rms arc sec. (nice)  But the RA still kicks and makes for double stars.  My dec was still poor so I'll regrease dec next and check
my alignment. (it's fairly perminent in a dome, but I have a tripod leg/mount and it "can move".  I usually check alignment 1-2 times a year or when ever guiding quality decreases. 
I am not aware of any gear scraping - I always release it clean...  I have on 3-4 occasions allowed it to track into a leg and (stop). Not sure if that hurts anything. But seems to work fine next time.

I don't understand why the RA kick changed from lower to higher (E to W?) the mount orientation did not change. 
I'll swap the part positions over and try again tonight.  During regreasing/cleaning I saw nothing strange. No chunks or crud.  old Grease moved quickly,  freely. not at all gummy. 
I have some pics n video.



On Thu, Jun 18, 2020 at 3:39 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Hello Ron,

Howard won't be able to answer you at this time.

Can you do a test for me?

With keypad in Autostart NO, send the mount to Park1 and turn off power.
Loosen the clutches and move the mount to Park5 manually.
Turn power back on and press "Resume from Park5"

Now check to see if the RA anomaly persists. let me know the results and we can go from there.

By the way, your screen shot is so blurry I cannot make out any details on it.

Rolando



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 1:35 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:
Ron,
 
Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.
 
Try regreasing first and contact us again if you can’t resolve the issue.
 
Clear Skies,
 
Marj Christen
Astro-Physics, Inc
11250 Forest Hills Rd
Machesney Park, IL 61115
Phone: 815-282-1513
Fax: 815-282-9847
 
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist
 
I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 
I ordered the grease, I'll see how that goes.
 
 
On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.
 
You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.
 
Rolando
 
 
 
-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist
My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  
Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately
the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.
Nothing I have tried to far has fixed it.
I will include the log from a couple nights ago to show what I mean. 
I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  
I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  
I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 
 
 

 
--


--


--


--


--


--
Brian 



Brian Valente


Re: Mach1 problem please assist

 

those big offsets and changing directions look an awful lot like the spiral dither pattern in PHD


On Thu, Jun 18, 2020 at 2:11 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
The graph shows 7 RA motions in the down direction, then a number of RA moves in the opposite direction. Is this over a period of time continuously? In other words, was this graph taken without interruption?

Roland



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 3:42 pm
Subject: Re: [ap-gto] Mach1 problem please assist

Capture is CLEAR and sharp. not sure what "GROUPS" does to images. I hate GROUPS.  Forums are better and allow you to retain/library of topics and Q&A, = (
I'll attach it again.  Is there a limit? size? restriction?    I'll attach at ORIGINAL SIZE


RA KICK.JPG

On Thu, Jun 18, 2020 at 4:37 PM Ron Kramer <ronkramer1957@...> wrote:
I don't own use a keypad.   I did try that SWAP OVER - but I then cleaned it and not sure where it ended up.  Since the last test clearly had the saime  KICKS. I can do ig again.  
What does that do?  I think it might track toward the other side of the groove?  I'll swap it over again and see if it helps since re-greasing.

NICELY - greasing lowered my RA RMA error almost 50%.  Here is my history.

Mount arrived. I guided around 1.0.  Always trying to tweak it - not sure why but months later I was guiding at  .24 RMS error (arc set). yeah - that's awesome.
MANY months of that... The RASA guided better than my long APO.  But late winter I swapped RASA V1 for a RASA V2 (heavier) and ever since my guiding was 1.5 average.  My image scale is 1.69 
lately - the RA kicks put me into  1.7-2.0.  I get double stars on every other sub. 
I re-greased the RA and last night afterwards I was 1.1max and usuall around .89 tot rms arc sec. (nice)  But the RA still kicks and makes for double stars.  My dec was still poor so I'll regrease dec next and check
my alignment. (it's fairly perminent in a dome, but I have a tripod leg/mount and it "can move".  I usually check alignment 1-2 times a year or when ever guiding quality decreases. 
I am not aware of any gear scraping - I always release it clean...  I have on 3-4 occasions allowed it to track into a leg and (stop). Not sure if that hurts anything. But seems to work fine next time.

I don't understand why the RA kick changed from lower to higher (E to W?) the mount orientation did not change. 
I'll swap the part positions over and try again tonight.  During regreasing/cleaning I saw nothing strange. No chunks or crud.  old Grease moved quickly,  freely. not at all gummy. 
I have some pics n video.



On Thu, Jun 18, 2020 at 3:39 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Hello Ron,

Howard won't be able to answer you at this time.

Can you do a test for me?

With keypad in Autostart NO, send the mount to Park1 and turn off power.
Loosen the clutches and move the mount to Park5 manually.
Turn power back on and press "Resume from Park5"

Now check to see if the RA anomaly persists. let me know the results and we can go from there.

By the way, your screen shot is so blurry I cannot make out any details on it.

Rolando



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 1:35 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:
Ron,
 
Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.
 
Try regreasing first and contact us again if you can’t resolve the issue.
 
Clear Skies,
 
Marj Christen
Astro-Physics, Inc
11250 Forest Hills Rd
Machesney Park, IL 61115
Phone: 815-282-1513
Fax: 815-282-9847
 
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist
 
I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 
I ordered the grease, I'll see how that goes.
 
 
On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.
 
You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.
 
Rolando
 
 
 
-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist
My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  
Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately
the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.
Nothing I have tried to far has fixed it.
I will include the log from a couple nights ago to show what I mean. 
I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  
I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  
I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 
 
 

 
--


--


--


--


--



--
Brian 



Brian Valente


Re: Mach1 problem please assist

Roland Christen
 

The graph shows 7 RA motions in the down direction, then a number of RA moves in the opposite direction. Is this over a period of time continuously? In other words, was this graph taken without interruption?

Roland



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 3:42 pm
Subject: Re: [ap-gto] Mach1 problem please assist

Capture is CLEAR and sharp. not sure what "GROUPS" does to images. I hate GROUPS.  Forums are better and allow you to retain/library of topics and Q&A, = (
I'll attach it again.  Is there a limit? size? restriction?    I'll attach at ORIGINAL SIZE


RA KICK.JPG

On Thu, Jun 18, 2020 at 4:37 PM Ron Kramer <ronkramer1957@...> wrote:
I don't own use a keypad.   I did try that SWAP OVER - but I then cleaned it and not sure where it ended up.  Since the last test clearly had the saime  KICKS. I can do ig again.  
What does that do?  I think it might track toward the other side of the groove?  I'll swap it over again and see if it helps since re-greasing.

NICELY - greasing lowered my RA RMA error almost 50%.  Here is my history.

Mount arrived. I guided around 1.0.  Always trying to tweak it - not sure why but months later I was guiding at  .24 RMS error (arc set). yeah - that's awesome.
MANY months of that... The RASA guided better than my long APO.  But late winter I swapped RASA V1 for a RASA V2 (heavier) and ever since my guiding was 1.5 average.  My image scale is 1.69 
lately - the RA kicks put me into  1.7-2.0.  I get double stars on every other sub. 
I re-greased the RA and last night afterwards I was 1.1max and usuall around .89 tot rms arc sec. (nice)  But the RA still kicks and makes for double stars.  My dec was still poor so I'll regrease dec next and check
my alignment. (it's fairly perminent in a dome, but I have a tripod leg/mount and it "can move".  I usually check alignment 1-2 times a year or when ever guiding quality decreases. 
I am not aware of any gear scraping - I always release it clean...  I have on 3-4 occasions allowed it to track into a leg and (stop). Not sure if that hurts anything. But seems to work fine next time.

I don't understand why the RA kick changed from lower to higher (E to W?) the mount orientation did not change. 
I'll swap the part positions over and try again tonight.  During regreasing/cleaning I saw nothing strange. No chunks or crud.  old Grease moved quickly,  freely. not at all gummy. 
I have some pics n video.



On Thu, Jun 18, 2020 at 3:39 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Hello Ron,

Howard won't be able to answer you at this time.

Can you do a test for me?

With keypad in Autostart NO, send the mount to Park1 and turn off power.
Loosen the clutches and move the mount to Park5 manually.
Turn power back on and press "Resume from Park5"

Now check to see if the RA anomaly persists. let me know the results and we can go from there.

By the way, your screen shot is so blurry I cannot make out any details on it.

Rolando



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 1:35 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:
Ron,
 
Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.
 
Try regreasing first and contact us again if you can’t resolve the issue.
 
Clear Skies,
 
Marj Christen
Astro-Physics, Inc
11250 Forest Hills Rd
Machesney Park, IL 61115
Phone: 815-282-1513
Fax: 815-282-9847
 
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist
 
I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 
I ordered the grease, I'll see how that goes.
 
 
On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.
 
You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.
 
Rolando
 
 
 
-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist
My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  
Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately
the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.
Nothing I have tried to far has fixed it.
I will include the log from a couple nights ago to show what I mean. 
I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  
I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  
I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 
 
 

 
--


--


--


--


--


Re: Mach1 problem please assist

Roland Christen
 

You can do the same thing using the ASCOM driver. Same routine as I described.

Roland



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 3:37 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I don't own use a keypad.   I did try that SWAP OVER - but I then cleaned it and not sure where it ended up.  Since the last test clearly had the saime  KICKS. I can do ig again.  
What does that do?  I think it might track toward the other side of the groove?  I'll swap it over again and see if it helps since re-greasing.

NICELY - greasing lowered my RA RMA error almost 50%.  Here is my history.

Mount arrived. I guided around 1.0.  Always trying to tweak it - not sure why but months later I was guiding at  .24 RMS error (arc set). yeah - that's awesome.
MANY months of that... The RASA guided better than my long APO.  But late winter I swapped RASA V1 for a RASA V2 (heavier) and ever since my guiding was 1.5 average.  My image scale is 1.69 
lately - the RA kicks put me into  1.7-2.0.  I get double stars on every other sub. 
I re-greased the RA and last night afterwards I was 1.1max and usuall around .89 tot rms arc sec. (nice)  But the RA still kicks and makes for double stars.  My dec was still poor so I'll regrease dec next and check
my alignment. (it's fairly perminent in a dome, but I have a tripod leg/mount and it "can move".  I usually check alignment 1-2 times a year or when ever guiding quality decreases. 
I am not aware of any gear scraping - I always release it clean...  I have on 3-4 occasions allowed it to track into a leg and (stop). Not sure if that hurts anything. But seems to work fine next time.

I don't understand why the RA kick changed from lower to higher (E to W?) the mount orientation did not change. 
I'll swap the part positions over and try again tonight.  During regreasing/cleaning I saw nothing strange. No chunks or crud.  old Grease moved quickly,  freely. not at all gummy. 
I have some pics n video.



On Thu, Jun 18, 2020 at 3:39 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Hello Ron,

Howard won't be able to answer you at this time.

Can you do a test for me?

With keypad in Autostart NO, send the mount to Park1 and turn off power.
Loosen the clutches and move the mount to Park5 manually.
Turn power back on and press "Resume from Park5"

Now check to see if the RA anomaly persists. let me know the results and we can go from there.

By the way, your screen shot is so blurry I cannot make out any details on it.

Rolando



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 1:35 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:
Ron,
 
Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.
 
Try regreasing first and contact us again if you can’t resolve the issue.
 
Clear Skies,
 
Marj Christen
Astro-Physics, Inc
11250 Forest Hills Rd
Machesney Park, IL 61115
Phone: 815-282-1513
Fax: 815-282-9847
 
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist
 
I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 
I ordered the grease, I'll see how that goes.
 
 
On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.
 
You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.
 
Rolando
 
 
 
-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist
My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  
Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately
the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.
Nothing I have tried to far has fixed it.
I will include the log from a couple nights ago to show what I mean. 
I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  
I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  
I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 
 
 

 
--


--


--


--


Re: Mach1 problem please assist

Ron Kramer
 

Capture is CLEAR and sharp. not sure what "GROUPS" does to images. I hate GROUPS.  Forums are better and allow you to retain/library of topics and Q&A, = (
I'll attach it again.  Is there a limit? size? restriction?    I'll attach at ORIGINAL SIZE


RA KICK.JPG

On Thu, Jun 18, 2020 at 4:37 PM Ron Kramer <ronkramer1957@...> wrote:
I don't own use a keypad.   I did try that SWAP OVER - but I then cleaned it and not sure where it ended up.  Since the last test clearly had the saime  KICKS. I can do ig again.  
What does that do?  I think it might track toward the other side of the groove?  I'll swap it over again and see if it helps since re-greasing.

NICELY - greasing lowered my RA RMA error almost 50%.  Here is my history.

Mount arrived. I guided around 1.0.  Always trying to tweak it - not sure why but months later I was guiding at  .24 RMS error (arc set). yeah - that's awesome.
MANY months of that... The RASA guided better than my long APO.  But late winter I swapped RASA V1 for a RASA V2 (heavier) and ever since my guiding was 1.5 average.  My image scale is 1.69 
lately - the RA kicks put me into  1.7-2.0.  I get double stars on every other sub. 
I re-greased the RA and last night afterwards I was 1.1max and usuall around .89 tot rms arc sec. (nice)  But the RA still kicks and makes for double stars.  My dec was still poor so I'll regrease dec next and check
my alignment. (it's fairly perminent in a dome, but I have a tripod leg/mount and it "can move".  I usually check alignment 1-2 times a year or when ever guiding quality decreases. 
I am not aware of any gear scraping - I always release it clean...  I have on 3-4 occasions allowed it to track into a leg and (stop). Not sure if that hurts anything. But seems to work fine next time.

I don't understand why the RA kick changed from lower to higher (E to W?) the mount orientation did not change. 
I'll swap the part positions over and try again tonight.  During regreasing/cleaning I saw nothing strange. No chunks or crud.  old Grease moved quickly,  freely. not at all gummy. 
I have some pics n video.



On Thu, Jun 18, 2020 at 3:39 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Hello Ron,

Howard won't be able to answer you at this time.

Can you do a test for me?

With keypad in Autostart NO, send the mount to Park1 and turn off power.
Loosen the clutches and move the mount to Park5 manually.
Turn power back on and press "Resume from Park5"

Now check to see if the RA anomaly persists. let me know the results and we can go from there.

By the way, your screen shot is so blurry I cannot make out any details on it.

Rolando



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 1:35 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:
Ron,
 
Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.
 
Try regreasing first and contact us again if you can’t resolve the issue.
 
Clear Skies,
 
Marj Christen
Astro-Physics, Inc
11250 Forest Hills Rd
Machesney Park, IL 61115
Phone: 815-282-1513
Fax: 815-282-9847
 
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist
 
I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 
I ordered the grease, I'll see how that goes.
 
 
On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.
 
You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.
 
Rolando
 
 
 
-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist
My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  
Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately
the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.
Nothing I have tried to far has fixed it.
I will include the log from a couple nights ago to show what I mean. 
I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  
I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  
I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 
 
 

 
--


--


--



--



Re: Mach1 problem please assist

Ron Kramer
 

I don't own use a keypad.   I did try that SWAP OVER - but I then cleaned it and not sure where it ended up.  Since the last test clearly had the saime  KICKS. I can do ig again.  
What does that do?  I think it might track toward the other side of the groove?  I'll swap it over again and see if it helps since re-greasing.

NICELY - greasing lowered my RA RMA error almost 50%.  Here is my history.

Mount arrived. I guided around 1.0.  Always trying to tweak it - not sure why but months later I was guiding at  .24 RMS error (arc set). yeah - that's awesome.
MANY months of that... The RASA guided better than my long APO.  But late winter I swapped RASA V1 for a RASA V2 (heavier) and ever since my guiding was 1.5 average.  My image scale is 1.69 
lately - the RA kicks put me into  1.7-2.0.  I get double stars on every other sub. 
I re-greased the RA and last night afterwards I was 1.1max and usuall around .89 tot rms arc sec. (nice)  But the RA still kicks and makes for double stars.  My dec was still poor so I'll regrease dec next and check
my alignment. (it's fairly perminent in a dome, but I have a tripod leg/mount and it "can move".  I usually check alignment 1-2 times a year or when ever guiding quality decreases. 
I am not aware of any gear scraping - I always release it clean...  I have on 3-4 occasions allowed it to track into a leg and (stop). Not sure if that hurts anything. But seems to work fine next time.

I don't understand why the RA kick changed from lower to higher (E to W?) the mount orientation did not change. 
I'll swap the part positions over and try again tonight.  During regreasing/cleaning I saw nothing strange. No chunks or crud.  old Grease moved quickly,  freely. not at all gummy. 
I have some pics n video.



On Thu, Jun 18, 2020 at 3:39 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Hello Ron,

Howard won't be able to answer you at this time.

Can you do a test for me?

With keypad in Autostart NO, send the mount to Park1 and turn off power.
Loosen the clutches and move the mount to Park5 manually.
Turn power back on and press "Resume from Park5"

Now check to see if the RA anomaly persists. let me know the results and we can go from there.

By the way, your screen shot is so blurry I cannot make out any details on it.

Rolando



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 1:35 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:
Ron,
 
Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.
 
Try regreasing first and contact us again if you can’t resolve the issue.
 
Clear Skies,
 
Marj Christen
Astro-Physics, Inc
11250 Forest Hills Rd
Machesney Park, IL 61115
Phone: 815-282-1513
Fax: 815-282-9847
 
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist
 
I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 
I ordered the grease, I'll see how that goes.
 
 
On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.
 
You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.
 
Rolando
 
 
 
-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist
My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  
Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately
the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.
Nothing I have tried to far has fixed it.
I will include the log from a couple nights ago to show what I mean. 
I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  
I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  
I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 
 
 

 
--


--


--




Re: Mach1 problem please assist

Roland Christen
 

6.4 minutes would indicate 1 worm cycle.

There are two possibilities. A nick in the worm or a defect in the worm wheel teeth. The test I suggested in my previous post will determine which one.

Rolando



-----Original Message-----
From: Michael Hambrick via groups.io <mike.hambrick@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 2:45 pm
Subject: Re: [ap-gto] Mach1 problem please assist

What is the time interval of those spikes ? The intervals all look to be the same which definitely suggests a worm issue.


Best Regards

Michael Hambrick
ARLANXEO
TSR Global Manufacturing Support
PO Box 2000
Orange, TX 77631-2000
Phone: +1 (409) 882-2799
email: mike.hambrick@...


Re: Mach1 problem please assist

Michael Hambrick <mike.hambrick@...>
 

What is the time interval of those spikes ? The intervals all look to be the same which definitely suggests a worm issue.


Best Regards

Michael Hambrick
ARLANXEO
TSR Global Manufacturing Support
PO Box 2000
Orange, TX 77631-2000
Phone: +1 (409) 882-2799
email: mike.hambrick@...


Re: Mach1 problem please assist

Roland Christen
 

Hello Ron,

Howard won't be able to answer you at this time.

Can you do a test for me?

With keypad in Autostart NO, send the mount to Park1 and turn off power.
Loosen the clutches and move the mount to Park5 manually.
Turn power back on and press "Resume from Park5"

Now check to see if the RA anomaly persists. let me know the results and we can go from there.

By the way, your screen shot is so blurry I cannot make out any details on it.

Rolando



-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 1:35 pm
Subject: Re: [ap-gto] Mach1 problem please assist

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:
Ron,
 
Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.
 
Try regreasing first and contact us again if you can’t resolve the issue.
 
Clear Skies,
 
Marj Christen
Astro-Physics, Inc
11250 Forest Hills Rd
Machesney Park, IL 61115
Phone: 815-282-1513
Fax: 815-282-9847
 
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist
 
I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 
I ordered the grease, I'll see how that goes.
 
 
On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:
Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.
 
You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.
 
Rolando
 
 
 
-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist
My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  
Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately
the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.
Nothing I have tried to far has fixed it.
I will include the log from a couple nights ago to show what I mean. 
I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  
I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  
I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 
 
 

 
--


--


--


Re: PEMPro on ASI6200 & QHY600

Bill Long
 

That's good. We've had nothing but clouds here for weeks. Might get some clearing early next week.


From: main@ap-gto.groups.io <main@ap-gto.groups.io> on behalf of Dale Ghent <daleg@...>
Sent: Wednesday, June 17, 2020 8:16 PM
To: main@ap-gto.groups.io <main@ap-gto.groups.io>
Subject: Re: [ap-gto] PEMPro on ASI6200 & QHY600
 

Oh, I have a QHY600 now. I can help test this.

> On Jun 17, 2020, at 10:48 PM, Ray Gralak <groups3@...> wrote:
>
> Hi Tom,
>
>> Any progress on this? I have heard that it was a couple of days away a couple of weeks ago.
>
> PEMPro 3.0.29 was released a couple weeks ago and I am waiting for feedback. The only change required was to add full support for subframes and binning in the polar alignment wizard. PEC programming did not require any changes.
>
> -Ray Gralak
> Author of APCC (Astro-Physics Command Center): https://www.astro-physics.com/apcc-pro
> Author of PEMPro V3:  https://www.ccdware.com
> Author of Astro-Physics V2 ASCOM Driver: https://www.siriusimaging.com/apdriver
>
>
>> -----Original Message-----
>> From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Tom Blahovici
>> Sent: Wednesday, June 17, 2020 3:54 PM
>> To: main@ap-gto.groups.io
>> Subject: Re: [ap-gto] PEMPro on ASI6200 & QHY600
>>
>> Hi
>> Any progress on this? I have heard that it was a couple of days away a couple of weeks ago.
>> Thanks, Tom
>>
>
>
>
>





Re: Mach1 problem please assist

Ron Kramer
 

I re-greased the RA.  It was really relaxing and nothing to fear.  No springs jumped out at me or other crazy surprises. 
The first test last night showed my RA improved by almost 50% reduction in RA RMS error.  (I'm shocked).

On the bad side, I did not fix my RA KICK problem.  I did not see RA worm flaws except on the very end (3 turns) of the worm and I'm sure that is never in contact with the drive gear.
I have emailed Howard... but wondered if it helps determine the problem from last night's guide log.  I was surprised to see it FLIPPED the RA kick.  (no meridian flip took place) why would it flip? 


RA KICK.JPG

On Wed, Jun 17, 2020 at 4:21 PM Ron Kramer via groups.io <ronkramer1957=gmail.com@groups.io> wrote:
Kit arrived late last night. (UPS error)
Today it was hot in the dome so I just did the RA worm and drive gear. And the side gears)
I hope to test tonight and see if it solves my RA kicking problem. 

I inspected the worm and was in fine shape - EXCEPT I had some very rough area which I don't think matters. It was way over on the very edges of the worm... like the last 2-3 turns were rough. I don't believe this are ever used? 

I greased the entire worm even though it said just the center is all that's needed. Figured it would help ward off corrosion.   The process wasn't scary once the RA box was removed. In fact (I don't recommend this) but I didn't even take my gear off the mount.  RASA 11 + essentials upside down at times.   I forgot about the cords but never turned more than 180.  I actually read the instructions after I was done. (common for me, I like to dig in) then see what I did wrong. 

SOUNDS nice... Will see if the RA hiccups tonight in a guiding test.  if all is good I'll do DEC tomorrow but RA was a primary concern as it would jump and killed every other sub.

Will see tonight.





On Wed, Jun 10, 2020 at 4:33 PM Marj Christen <marj@...> wrote:

Ron,

 

Now that our production staff has returned, the turnaround time for repairs is pretty quick. There is no standard cost for a “ tune up” since it depends on what is involved and if parts have to be replaced.

 

Try regreasing first and contact us again if you can’t resolve the issue.

 

Clear Skies,

 

Marj Christen

Astro-Physics, Inc

11250 Forest Hills Rd

Machesney Park, IL 61115

Phone: 815-282-1513

Fax: 815-282-9847

www.astro-physics.com

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Ron Kramer
Sent: Wednesday, June 10, 2020 1:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 problem please assist

 

I'm about to try to re-grease - I'll see if I can see something during inspection.  Is swapping the worm something easy I can do at home? 
I don't want to do anything complicated. I don't believe I've nicked a gear - I only use park3.  But it has come against the pier during a few 3-4 occasions? Would that do anything?

How much does it cost to send it in for a tune up?  HOW LONG would I be without it?  I'm near in Grand Rapids, MI.
I'll look for a clump of anything in the worm teeth.  If I send it in I don 't want it waiting for weeks/days. What is time frame? 

I ordered the grease, I'll see how that goes.

 

 

On Tue, Jun 9, 2020 at 7:51 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:

Forget backlash in RA. There is no such thing. RA always tracks so it never reverses. Backlash does not enter into tracking.

 

You may have damaged your worm teeth when you backed off the worm to do a fine balance. You may have forgotten to do it only in the Park3 position. If that's the case, the worm may have a nick in the teeth and it will show up as a repeating pattern once every 6.4 minutes.

 

Rolando

 

 

 

-----Original Message-----
From: Ron Kramer <ronkramer1957@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 9, 2020 3:30 pm
Subject: [ap-gto] Mach1 problem please assist

My mach1 is about 2.5 years old.  I was getting awesome guiding with a total rms error of .24 arc sec.  

Winter came and went and this spring it's been horrible.  like  1.4.   My image scale is about 1.69 so I lived with that for a while, but lately

the RA is  KICKING in almost a timely fashion.  One of these kicks makes double stars.  Around 1/2 my subs have to be deleted.

Nothing I have tried to far has fixed it.

I will include the log from a couple nights ago to show what I mean. 

I did a new calibration - then a guide assistant for a while... then set recommendations and let it guide a while.
You'll see   RA  kicking like a mule in a rather evenly timed fashion!?!  

I would so appreciate help with this.  Someone in PHD said make sure the mount software/HC doesn't have backlash on.  

I DO NOT USE or own a HC and I don't know of any BackLash setting in APCC pro.  I'm going nuts. 

 

 


 

--



--




Re: Messier 13 with 10in Newtonian and AP 1100GTO mount

Roland Christen
 

An excellent rendition of that famous object. Colors nicely preserved, very well processed.

Rolando



-----Original Message-----
From: Luca Marinelli <photo@...>
To: main@ap-gto.groups.io
Sent: Thu, Jun 18, 2020 10:54 am
Subject: [ap-gto] Messier 13 with 10in Newtonian and AP 1100GTO mount

I have been imaging with a TS ONTC 10in f4 Newtonian scope for a couple of years (40lbs with all the bells and whistles attached and just about a meter long). I had it mounted on a latest generation AP Mach1GTO mount and this Spring I bought an AP 1100GTO from a ap-gto fellow subscriber. I expected to find significant improvement in the atmospheric conditions it could handle but I was pleasantly surprised at how much tighter and rounder stars were under pretty much all circumstances. I couldn't be happier with the combination of the AP 1100GTO and APPC Pro. It truly just works night in and night out.

The first image I was processed with this imaging system is a deep view of Messier 13. I annotated all the galaxies in the field of view using the Hyperleda catalog and you can find smudges in the image corresponding to galaxies down to roughly magnitude 22.5. This image was awarded Astrobin's Image of the Day today. The annotated images can be found on my Astrobin page, if you are interested:

https://astrob.in/ydk4cz/0/

I hope you enjoy the images!

Cheers,

Luca


Re: Mach1 - regreasing

Fernando Proietti
 

Hi Karen,

Many thanks, regards, FerNANDO

Em ter., 16 de jun. de 2020 às 16:34, Karen Christen <karen@...> escreveu:

Hi Fernando,

 

I’ve attached directions to remove the auto-adjusting gearbox that you have on your Mach1.  Once you have the gearbox off you may proceed with re-greasing.

Karen Christen

Astro-Physics

 

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of uncarollo2 <chris1011@...> via groups.io
Sent: Tuesday, June 16, 2020 2:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 - regreasing

 

You have the latest gearbox. Karen will send you instructions how to disassemble it.

 

Rolando

 

 

 

-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 1:52 pm
Subject: Re: [ap-gto] Mach1 - regreasing

Hi Rolando,

 

Photos attached, thanks, Fernando

 

Em ter., 16 de jun. de 2020 às 11:06, uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> escreveu:

Can you send a picture of your mount's gearbox from 2 sides so we can see which model you have?

 

Rolando

 

 

 

-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 8:53 am
Subject: [ap-gto] Mach1 - regreasing

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando


--
Karen Christen
Astro-Physics


Re: PEMPro on ASI6200 & QHY600

Tom Blahovici
 

Hi,

Ok thanks.  I noticed there was an update but nothing mentioned in the release notes.
I'll give it a try when I can.
73 Tom


Re: What is the diameter and thread on the Pasil.4 polar scope?

Tom Blahovici
 

Hi
Perfect.  Thanks very much!  This will be my first time threading....
Best regards, Tom


Re: Messier 13 with 10in Newtonian and AP 1100GTO mount

Dean Jacobsen
 

Great image Luca.  The colorful stars are very nice.
--
Dean Jacobsen
http://astrophoto.net/wp/ 
Image Gallery - http://astrophoto.net/wp/image-gallery/
Astrobin - https://www.astrobin.com/users/deanjacobsen/ 

8601 - 8620 of 79811