Date   

Re: Point Mapping Strategies for the Mobile Imager

Dean Jacobsen
 

On Sun, Jun 14, 2020 at 09:35 PM, Dean Jacobsen wrote:



 
Still looking for opinions regarding success or cautions regarding point mapping runs which are specific to the path a particular target will take during the course of a night.  If a scheme like this works then it would be helpful for those of us who setup and take down their rigs nightly.
--
Dean Jacobsen
http://astrophoto.net/wp/ 
Image Gallery - http://astrophoto.net/wp/image-gallery/
Astrobin - https://www.astrobin.com/users/deanjacobsen/ 


Re: help with AP900 guiding via ASIAir Pro

Ray Gralak
 

Hi Steve,

I see the problem. The old firmware that you have (Rev 'E' chip) requires separate start and stop commands to issue guider moves, but the driver is sending timed moves. Timed moves handle starting (and stopping a guider move after the supplied duration value) from within the control box.

However, I think the old firmware in your mount is handling this as a simple start move and the move continues while waiting for a stop command. Since the driver expects the control box to stop the move after the supplied duration, the driver does not send a stop move command. Thus, the GTOCP2 firmware keeps the guider move going until you stopped it with an appropriate key press on the keypad.

I think you should be able to fix this problem by selecting the correct mount type and controller in the AP V2 driver setup. That is, make sure you have AP900 as the mount type and GTOCP2 as the controller. In one of your logs you have GTOCP4 selected as the controller and no mount type. This will cause the driver to potentially send commands that the GTOCP2 will not understand, like the timed moves.

-Ray Gralak
Author of APCC (Astro-Physics Command Center): https://www.astro-physics.com/apcc-pro
Author of PEMPro V3: https://www.ccdware.com
Author of Astro-Physics V2 ASCOM Driver: https://www.siriusimaging.com/apdriver

-----Original Message-----
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of sgbonnell@outlook.com
Sent: Tuesday, June 16, 2020 7:07 AM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] help with AP900 guiding via ASIAir Pro

Hi Ray,
ASCOM driver logs attached...thanks!
Steve


Re: APCC and APPM is amazing

 

Just to close that out, we believe the reflections are caused by a missing baffle around the main mirror on the planewave cdk17. very unusual this happened, but a fix is in the works

Brian

On Tue, Jun 16, 2020 at 7:44 AM myrussellm via groups.io <mikerussell63=protonmail.com@groups.io> wrote:
Barry

Apologies, replied to the wrong post - the other image was with a planewave scope having six reflections in the image

Cheers

Mike 



--
Brian 



Brian Valente


Re: APCC and APPM is amazing

myrussellm
 

Barry

Apologies, replied to the wrong post - the other image was with a planewave scope having six reflections in the image

Cheers

Mike 


Re: help with AP900 guiding via ASIAir Pro

sgbonnell@...
 

Hi Ray,
ASCOM driver logs attached...thanks!
Steve


Re: Mach1 - regreasing

Roland Christen
 

Can you send a picture of your mount's gearbox from 2 sides so we can see which model you have?

Rolando



-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 8:53 am
Subject: [ap-gto] Mach1 - regreasing

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando



Mach1 - regreasing

Fernando Proietti
 

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando



Re: help with AP900 guiding via ASIAir Pro

Ray Gralak
 

Yes, found the Cal file - I've attached. The guide star is lost at the start of Cal, so Cal does not get
completed.
Can you also post the AP V2 ASCOM driver log file so that we can see what the driver was doing?

-Ray Gralak
Author of APCC (Astro-Physics Command Center): https://www.astro-physics.com/apcc-pro
Author of PEMPro V3: https://www.ccdware.com
Author of Astro-Physics V2 ASCOM Driver: https://www.siriusimaging.com/apdriver


-----Original Message-----
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of sgbonnell@outlook.com
Sent: Monday, June 15, 2020 11:15 AM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] help with AP900 guiding via ASIAir Pro

Yes, found the Cal file - I've attached. The guide star is lost at the start of Cal, so Cal does not get
completed.

When using PHD2 for guiding, I have the mount connected directly to my PC via the RS232 to USB cable.
Same set up when using ASIAir...USB end of the cable is plugged into the USB port on the ASIAir.
I just recently downloaded the latest A-P ASCOM driver from Ray G....my mount was a GTO2, but has been
upgraded to GTO4.

I have been using this same set up until recently on my Celestron CGX-L with no issues...it was only when I
started using ASIAir or PHD2 on the AP900 that I have had this issue..


Re: Sky Safari with Mach2

Christopher Erickson
 

Until they get over themselves and add Park3, I have given up on SkySafari too.

I have been asking them for Park3 for YEARS. 

-Christopher Erickson
Observatory engineer
Waikoloa, HI 96738
www.summitkinetics.com
   


On Mon, Jun 15, 2020, 7:16 PM Donald Rudny <mkea13800@...> wrote:
Hi All,

I just gave up on SkySafari and switched to Luminos.  I had to use APCC to initialize to P3.  Luminos lets you initialize in any position and has more controls of the mount like slewing and tracking rates.  I control everything with my iPad and Luminos.  No keypad.  
For $29.95 for Luminos and a smartphone or tablet you have your keypad.  I loved SkySafari, but their failure to provide more positions for initialization on AP mounts lost me as a supporter.

Don Rudny
Pepeekeo, Hi

On Jun 15, 2020, at 6:57 PM, Christopher Erickson <christopher.k.erickson@...> wrote:


PUH-LEEZE ask them to add Park3 too...


-Christopher Erickson
Observatory engineer
Waikoloa, HI 96738
www.summitkinetics.com
   

On Mon, Jun 15, 2020, 6:27 PM Marj Christen <marj@...> wrote:

We are working with Simulation Curriculum.

 

Clear Skies,

 

Marj Christen

Astro-Physics, Inc

11250 Forest Hills Rd

Machesney Park, IL 61115

Phone: 815-282-0910

Fax: 815-282-9847

www.astro-physics.com

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Dominique Durand via groups.io
Sent: Monday, June 15, 2020 12:02 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

On Mon, Jun 15, 2020 at 03:27 PM, Terri Zittritsch wrote:

Thanks Dominique, have you gotten any feedback from A-P or Simulation Curriculum?    I was wondering if it's normal, per past correspondence I've read about needing some initialization.  I know Sky Safari has a switch to pass time/location, but not sure that this does the trick.  I guess I'll wait to hear.  
I am an early adopter of Sky Safari and had every version since the beginning..  it is my favorite sky mapping program so hope that it'll be usable on the Mach2.    Maybe after getting the hand control sw.

Hi Terri,
I still have a doubt about this case that I had detected, because with my mach1 GTOCP4 that I had before I always had the keypad plugged in and I think that (Like the PC) was enough for Skysafari to synchronize, with my Mach1 GTOCP3 which I still have I pass for the WIFI by SkyFi3, that works for skysafari but there also I have a connected keypad.
My biggest concern and that I did not have with my GTOCP4 is that the WIFI network of the GTOCP5 disappears when the GTOCP5 is plugged into the PC, a problem linked to the USB3 sockets of my PC, because I plug into a USB2 socket it works .


Re: Sky Safari with Mach2

Woody Schlom
 

Good luck on that!  SkySafari hasn’t been the same since they sold out to Simulation Curriculum.  It’s still a great APP and I use it all the time, but support and feature requests have kind of gone down the toilet.

 

Woody

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Christopher Erickson
Sent: Monday, June 15, 2020 9:57 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

PUH-LEEZE ask them to add Park3 too...


-Christopher Erickson
Observatory engineer
Waikoloa, HI 96738
www.summitkinetics.com
   

 

On Mon, Jun 15, 2020, 6:27 PM Marj Christen <marj@...> wrote:

We are working with Simulation Curriculum.

 

Clear Skies,

 

Marj Christen

Astro-Physics, Inc

11250 Forest Hills Rd

Machesney Park, IL 61115

Phone: 815-282-0910

Fax: 815-282-9847

www.astro-physics.com

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Dominique Durand via groups.io
Sent: Monday, June 15, 2020 12:02 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

On Mon, Jun 15, 2020 at 03:27 PM, Terri Zittritsch wrote:

Thanks Dominique, have you gotten any feedback from A-P or Simulation Curriculum?    I was wondering if it's normal, per past correspondence I've read about needing some initialization.  I know Sky Safari has a switch to pass time/location, but not sure that this does the trick.  I guess I'll wait to hear.  
I am an early adopter of Sky Safari and had every version since the beginning..  it is my favorite sky mapping program so hope that it'll be usable on the Mach2.    Maybe after getting the hand control sw.

Hi Terri,
I still have a doubt about this case that I had detected, because with my mach1 GTOCP4 that I had before I always had the keypad plugged in and I think that (Like the PC) was enough for Skysafari to synchronize, with my Mach1 GTOCP3 which I still have I pass for the WIFI by SkyFi3, that works for skysafari but there also I have a connected keypad.
My biggest concern and that I did not have with my GTOCP4 is that the WIFI network of the GTOCP5 disappears when the GTOCP5 is plugged into the PC, a problem linked to the USB3 sockets of my PC, because I plug into a USB2 socket it works .


Re: Sky Safari with Mach2

Peter Nagy
 

The problem with Luminos is they require iPAD or iPhone products and they refuse to work with Android devices. Not good business since there are far more Android devices than Apple devices.

Peter


Re: Sky Safari with Mach2

Donald Rudny
 

Hi All,

I just gave up on SkySafari and switched to Luminos.  I had to use APCC to initialize to P3.  Luminos lets you initialize in any position and has more controls of the mount like slewing and tracking rates.  I control everything with my iPad and Luminos.  No keypad.  
For $29.95 for Luminos and a smartphone or tablet you have your keypad.  I loved SkySafari, but their failure to provide more positions for initialization on AP mounts lost me as a supporter.

Don Rudny
Pepeekeo, Hi

On Jun 15, 2020, at 6:57 PM, Christopher Erickson <christopher.k.erickson@...> wrote:


PUH-LEEZE ask them to add Park3 too...


-Christopher Erickson
Observatory engineer
Waikoloa, HI 96738
www.summitkinetics.com
   

On Mon, Jun 15, 2020, 6:27 PM Marj Christen <marj@...> wrote:

We are working with Simulation Curriculum.

 

Clear Skies,

 

Marj Christen

Astro-Physics, Inc

11250 Forest Hills Rd

Machesney Park, IL 61115

Phone: 815-282-0910

Fax: 815-282-9847

www.astro-physics.com

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Dominique Durand via groups.io
Sent: Monday, June 15, 2020 12:02 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

On Mon, Jun 15, 2020 at 03:27 PM, Terri Zittritsch wrote:

Thanks Dominique, have you gotten any feedback from A-P or Simulation Curriculum?    I was wondering if it's normal, per past correspondence I've read about needing some initialization.  I know Sky Safari has a switch to pass time/location, but not sure that this does the trick.  I guess I'll wait to hear.  
I am an early adopter of Sky Safari and had every version since the beginning..  it is my favorite sky mapping program so hope that it'll be usable on the Mach2.    Maybe after getting the hand control sw.

Hi Terri,
I still have a doubt about this case that I had detected, because with my mach1 GTOCP4 that I had before I always had the keypad plugged in and I think that (Like the PC) was enough for Skysafari to synchronize, with my Mach1 GTOCP3 which I still have I pass for the WIFI by SkyFi3, that works for skysafari but there also I have a connected keypad.
My biggest concern and that I did not have with my GTOCP4 is that the WIFI network of the GTOCP5 disappears when the GTOCP5 is plugged into the PC, a problem linked to the USB3 sockets of my PC, because I plug into a USB2 socket it works .


Re: Sky Safari with Mach2

Christopher Erickson
 

PUH-LEEZE ask them to add Park3 too...


-Christopher Erickson
Observatory engineer
Waikoloa, HI 96738
www.summitkinetics.com
   

On Mon, Jun 15, 2020, 6:27 PM Marj Christen <marj@...> wrote:

We are working with Simulation Curriculum.

 

Clear Skies,

 

Marj Christen

Astro-Physics, Inc

11250 Forest Hills Rd

Machesney Park, IL 61115

Phone: 815-282-0910

Fax: 815-282-9847

www.astro-physics.com

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Dominique Durand via groups.io
Sent: Monday, June 15, 2020 12:02 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

On Mon, Jun 15, 2020 at 03:27 PM, Terri Zittritsch wrote:

Thanks Dominique, have you gotten any feedback from A-P or Simulation Curriculum?    I was wondering if it's normal, per past correspondence I've read about needing some initialization.  I know Sky Safari has a switch to pass time/location, but not sure that this does the trick.  I guess I'll wait to hear.  
I am an early adopter of Sky Safari and had every version since the beginning..  it is my favorite sky mapping program so hope that it'll be usable on the Mach2.    Maybe after getting the hand control sw.

Hi Terri,
I still have a doubt about this case that I had detected, because with my mach1 GTOCP4 that I had before I always had the keypad plugged in and I think that (Like the PC) was enough for Skysafari to synchronize, with my Mach1 GTOCP3 which I still have I pass for the WIFI by SkyFi3, that works for skysafari but there also I have a connected keypad.
My biggest concern and that I did not have with my GTOCP4 is that the WIFI network of the GTOCP5 disappears when the GTOCP5 is plugged into the PC, a problem linked to the USB3 sockets of my PC, because I plug into a USB2 socket it works .


Re: Sky Safari with Mach2

 

We are working with Simulation Curriculum.

 

Clear Skies,

 

Marj Christen

Astro-Physics, Inc

11250 Forest Hills Rd

Machesney Park, IL 61115

Phone: 815-282-0910

Fax: 815-282-9847

www.astro-physics.com

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Dominique Durand via groups.io
Sent: Monday, June 15, 2020 12:02 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

On Mon, Jun 15, 2020 at 03:27 PM, Terri Zittritsch wrote:

Thanks Dominique, have you gotten any feedback from A-P or Simulation Curriculum?    I was wondering if it's normal, per past correspondence I've read about needing some initialization.  I know Sky Safari has a switch to pass time/location, but not sure that this does the trick.  I guess I'll wait to hear.  
I am an early adopter of Sky Safari and had every version since the beginning..  it is my favorite sky mapping program so hope that it'll be usable on the Mach2.    Maybe after getting the hand control sw.

Hi Terri,
I still have a doubt about this case that I had detected, because with my mach1 GTOCP4 that I had before I always had the keypad plugged in and I think that (Like the PC) was enough for Skysafari to synchronize, with my Mach1 GTOCP3 which I still have I pass for the WIFI by SkyFi3, that works for skysafari but there also I have a connected keypad.
My biggest concern and that I did not have with my GTOCP4 is that the WIFI network of the GTOCP5 disappears when the GTOCP5 is plugged into the PC, a problem linked to the USB3 sockets of my PC, because I plug into a USB2 socket it works .


Re: help with AP900 guiding via ASIAir Pro

Dean Jacobsen
 


Re: help with AP900 guiding via ASIAir Pro

 

>>> It really appears to me to be that somehow PHD2 (and ASIAir guiding - which borrows from PHD2) is sending something to the AP900 controller that turns off or stalls the tracking.  

okay now i'm less confused - you have the same thread going in the PHD forums.

PHD has no code that enables or disables tracking, as you know from Bruce's reply over there, so it's not originating from PHD2. 

If you are bouncing between PHD2 and ASIAir, it's probably better if you stick with PHD2 and resolve it first, then move to ASIAir. they are not transparent in what changes they've made to the app, so it's unclear how their custom version actually works

Brian

On Mon, Jun 15, 2020 at 3:20 PM uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> wrote:

GTO2 mount with an upgraded CP4 chip.
Again there is no GTO2 mount with CP4 chip. There is a 900 GTO mount. There is a CP4 servo controller which does not have chips. It is software programmable, whereas the older CP3 controllers were chip programmable.

In any case, a 900 mount with a CP4 servo controller should work properly with any external software such as PHD2. I am still totally confused about what the calibration star is doing. If the move commands are set at 450msec and you have entered the correct focal length, the guide star should move about 7 arc sec for each move command. In one direction the guide command would be to "Move East 450msec" and the motor would stop tracking for 450msec, which causes the star to move east 7 arc sec. Each 450msec command moves the star another 7 arc sec east. In the other direction the command would be "Move West 450msec". The motor will speed up to 2x sidereal and move 7 arc sec west. These Move East and Move West commands are interpreted by the ASCOM driver and sent to the mount. Normally that works perfectly fine.

Rolando


-----Original Message-----
To: main@ap-gto.groups.io
Sent: Mon, Jun 15, 2020 4:47 pm
Subject: Re: [ap-gto] help with AP900 guiding via ASIAir Pro

Sorry, mixed up my GTO's and CP's...it is an older GTO2 mount with an upgraded CP4 chip.

It really appears to me to be that somehow PHD2 (and ASIAir guiding - which borrows from PHD2) is sending something to the AP900 controller that turns off or stalls the tracking.  
Before I engage guiding, I can look at/image stars in 3-5 second loops for focusing and framing up and they stay tight and no position change.
As soon as I attempt to start Cal or Guiding from PHD2 or ASIAir, AP900 tracking stops, as confirmed when I again look at the images loops in focusing or previewing and the stars are trailed and moving.  My target of interest quickly moves off frame.
Even with PHD2 stopped, I need to cycle through the Rate control on the AP900 hand set and reset to SID rate and the mount begins to track again.  Otherwise mount tracking stays disabled.

I'll try Bryan's key pad testing suggestion.  I typically use either the AP900 hand controller, but mostly have been using the ASIAir for goto's and slewing/manual jogging..



--
Brian 



Brian Valente


Re: help with AP900 guiding via ASIAir Pro

Roland Christen
 


GTO2 mount with an upgraded CP4 chip.
Again there is no GTO2 mount with CP4 chip. There is a 900 GTO mount. There is a CP4 servo controller which does not have chips. It is software programmable, whereas the older CP3 controllers were chip programmable.

In any case, a 900 mount with a CP4 servo controller should work properly with any external software such as PHD2. I am still totally confused about what the calibration star is doing. If the move commands are set at 450msec and you have entered the correct focal length, the guide star should move about 7 arc sec for each move command. In one direction the guide command would be to "Move East 450msec" and the motor would stop tracking for 450msec, which causes the star to move east 7 arc sec. Each 450msec command moves the star another 7 arc sec east. In the other direction the command would be "Move West 450msec". The motor will speed up to 2x sidereal and move 7 arc sec west. These Move East and Move West commands are interpreted by the ASCOM driver and sent to the mount. Normally that works perfectly fine.

Rolando


-----Original Message-----
To: main@ap-gto.groups.io
Sent: Mon, Jun 15, 2020 4:47 pm
Subject: Re: [ap-gto] help with AP900 guiding via ASIAir Pro

Sorry, mixed up my GTO's and CP's...it is an older GTO2 mount with an upgraded CP4 chip.

It really appears to me to be that somehow PHD2 (and ASIAir guiding - which borrows from PHD2) is sending something to the AP900 controller that turns off or stalls the tracking.  
Before I engage guiding, I can look at/image stars in 3-5 second loops for focusing and framing up and they stay tight and no position change.
As soon as I attempt to start Cal or Guiding from PHD2 or ASIAir, AP900 tracking stops, as confirmed when I again look at the images loops in focusing or previewing and the stars are trailed and moving.  My target of interest quickly moves off frame.
Even with PHD2 stopped, I need to cycle through the Rate control on the AP900 hand set and reset to SID rate and the mount begins to track again.  Otherwise mount tracking stays disabled.

I'll try Bryan's key pad testing suggestion.  I typically use either the AP900 hand controller, but mostly have been using the ASIAir for goto's and slewing/manual jogging..


Re: help with AP900 guiding via ASIAir Pro

sgbonnell@...
 

Sorry, mixed up my GTO's and CP's...it is an older GTO2 mount with an upgraded CP4 chip.

It really appears to me to be that somehow PHD2 (and ASIAir guiding - which borrows from PHD2) is sending something to the AP900 controller that turns off or stalls the tracking.  
Before I engage guiding, I can look at/image stars in 3-5 second loops for focusing and framing up and they stay tight and no position change.
As soon as I attempt to start Cal or Guiding from PHD2 or ASIAir, AP900 tracking stops, as confirmed when I again look at the images loops in focusing or previewing and the stars are trailed and moving.  My target of interest quickly moves off frame.
Even with PHD2 stopped, I need to cycle through the Rate control on the AP900 hand set and reset to SID rate and the mount begins to track again.  Otherwise mount tracking stays disabled.

I'll try Bryan's key pad testing suggestion.  I typically use either the AP900 hand controller, but mostly have been using the ASIAir for goto's and slewing/manual jogging..


Re: help with AP900 guiding via ASIAir Pro

Roland Christen
 

I think the problem may be that the controller is a very old version CP2 which may have a chip in it that is not compatible. This appears to be a second hand mount and who knows what the first owner did to the controller.

Rolando



-----Original Message-----
From: Dean Jacobsen <deanjacobsen@...>
To: main@ap-gto.groups.io
Sent: Mon, Jun 15, 2020 4:04 pm
Subject: Re: [ap-gto] help with AP900 guiding via ASIAir Pro

On Mon, Jun 15, 2020 at 01:55 PM, Brian Valente wrote:
i really don't think that's what's going on
Well that is what he said above and the log that he posted says that the star is lost at the first calibration move. ;-)
 
--
Dean Jacobsen
http://astrophoto.net/wp/ 
Image Gallery - http://astrophoto.net/wp/image-gallery/
Astrobin - https://www.astrobin.com/users/deanjacobsen/ 


Re: help with AP900 guiding via ASIAir Pro

 

Dean sorry - i didn't mean to suggest you interpreted incorrectly, all i was saying is that the first move, if everything that was written is correct, was not likely the culprit of the lost star

someone else pointed out that should be a .5" move, so it's not moving out of the fov. sorry if I miscommunicated that 

On Mon, Jun 15, 2020 at 2:04 PM Dean Jacobsen <deanjacobsen@...> wrote:
On Mon, Jun 15, 2020 at 01:55 PM, Brian Valente wrote:
i really don't think that's what's going on
Well that is what he said above and the log that he posted says that the star is lost at the first calibration move. ;-)
 
--
Dean Jacobsen
http://astrophoto.net/wp/ 
Image Gallery - http://astrophoto.net/wp/image-gallery/
Astrobin - https://www.astrobin.com/users/deanjacobsen/ 



--
Brian 



Brian Valente

7281 - 7300 of 78420