|
Message Recall Failure: Recall: [ap-gto] APCC Pro MGBOX GPS connection
#APCC
By
WWyckoff at AT&T
·
#68889
·
|
|
Re: Mach2 Actual Location error - help!
Update - I rebooted both computer and CP5 my mount is back in Seattle. Terri, wonder if this was related to your mispointing? Do you remember if your site was correct?
|
Update - I rebooted both computer and CP5 my mount is back in Seattle. Terri, wonder if this was related to your mispointing? Do you remember if your site was correct?
|
By
Wayne Hixson
·
#68888
·
|
|
Mach2 Actual Location error - help!
My mount Actual Location is showing Latitude 0 and longitude 0 even when my site selected is Seattle? Refreshing doesn’t change it
|
My mount Actual Location is showing Latitude 0 and longitude 0 even when my site selected is Seattle? Refreshing doesn’t change it
|
By
Wayne Hixson
·
#68887
·
|
|
Re: Keypad Upgrade for Using Mach2
Thanks, I have a keypad that I hope to be able to upgrade to the new version when the mount arrives.
|
Thanks, I have a keypad that I hope to be able to upgrade to the new version when the mount arrives.
|
By
Dean Jacobsen
·
#68886
·
|
|
Re: GTOCP4 Not powering up
Wayne,
Thanks for the report. That’s way too funny!
Woody
|
Wayne,
Thanks for the report. That’s way too funny!
Woody
|
By
Woody Schlom
·
#68885
·
|
|
Re: GTOCP4 Not powering up
This has happened to me years ago on a different an AP1200.
One other suggestion as I think about it, if the mount looks like it’s getting no power at all, check out the center pin on the power
|
This has happened to me years ago on a different an AP1200.
One other suggestion as I think about it, if the mount looks like it’s getting no power at all, check out the center pin on the power
|
By
Lawrence Lopez
·
#68884
·
|
|
Re: GTOCP4 Not powering up
I’m hoping to get some actual time under clear skies, but ‘I’ll say so far in the exploratory period it’s exceeded expectations. I really appreciate the ability to not get lost. Clutches are a
|
I’m hoping to get some actual time under clear skies, but ‘I’ll say so far in the exploratory period it’s exceeded expectations. I really appreciate the ability to not get lost. Clutches are a
|
By
Wayne Hixson
·
#68883
·
|
|
Re: GTOCP4 Not powering up
Wayne you really need to get onto that Mach 2 report sir. 🤣
|
Wayne you really need to get onto that Mach 2 report sir. 🤣
|
By
Bill Long
·
#68882
·
|
|
Re: GTOCP4 Not powering up
Thanks everyone! We figured it out. This was the first time he’d had it out on a bright day.... you can tell where this is going. We went through a lot of the troubleshooting steps and all was fine.
|
Thanks everyone! We figured it out. This was the first time he’d had it out on a bright day.... you can tell where this is going. We went through a lot of the troubleshooting steps and all was fine.
|
By
Wayne Hixson
·
#68881
·
|
|
Re: GTOCP4 Not powering up
The OP says it’s a CP4 controller which I understand uses a different power connector. As I recall it’s a HiRose connector on the controller and the power cable has PP connectors on the other
|
The OP says it’s a CP4 controller which I understand uses a different power connector. As I recall it’s a HiRose connector on the controller and the power cable has PP connectors on the other
|
By
Woody Schlom
·
#68880
·
|
|
Re: GTOCP4 Not powering up
With Pyramids, if the P/S gets overloaded - e.g. short circuit in the cigarette lighter plug, or the screw-on terminals touching each other when tightened – the supply will shut down its output for
|
With Pyramids, if the P/S gets overloaded - e.g. short circuit in the cigarette lighter plug, or the screw-on terminals touching each other when tightened – the supply will shut down its output for
|
By
Joe Zeglinski
·
#68879
·
|
|
Message Recall Failure: Recall: [ap-gto] APCC Pro MGBOX GPS connection
#APCC
By
Mike Shade
·
#68878
·
|
|
Re: GTOCP4 Not powering up
I second the suggestion. Even better, try to power it from a fully charged 12v battery.
I had a Pyramid 20 amp power supply fail on me. This was as Oregon Star Party, and I was running the
|
I second the suggestion. Even better, try to power it from a fully charged 12v battery.
I had a Pyramid 20 amp power supply fail on me. This was as Oregon Star Party, and I was running the
|
By
W Hilmo
·
#68877
·
|
|
Re: Re : [ap-gto] APCC Standard 1.8.0.4 and APCC Pro 1.8.0.5 Pro
Thanks!
By
Wayne Hixson
·
#68876
·
|
|
Re: GTOCP4 Not powering up
Bad power cord, power supply polarity wrong, if using cigar plug check the wires inside the plug....
Rolando
|
Bad power cord, power supply polarity wrong, if using cigar plug check the wires inside the plug....
Rolando
|
By
Roland Christen
·
#68875
·
|
|
Re: Keypad Upgrade for Using Mach2
Yes. Keypads will follow shortly for those who ordered them.
Rolando
|
Yes. Keypads will follow shortly for those who ordered them.
Rolando
|
By
Roland Christen
·
#68874
·
|
|
Re: Keypad Upgrade for Using Mach2
Dean,
We hope to finish up the keypad program soon so that they can ship with the mounts. If your mount is ready before the keypad program is complete, our office staff will give you the option of
|
Dean,
We hope to finish up the keypad program soon so that they can ship with the mounts. If your mount is ready before the keypad program is complete, our office staff will give you the option of
|
By
Marj Christen
·
#68873
·
|
|
Re: GTOCP4 Not powering up
Even if that power supply has worked in the past, try a different one. I’ve had one Pyramid not only die on me, but almost take a couple of other pieces of equipment with it. Smoke suddenly coming
|
Even if that power supply has worked in the past, try a different one. I’ve had one Pyramid not only die on me, but almost take a couple of other pieces of equipment with it. Smoke suddenly coming
|
By
Woody Schlom
·
#68872
·
|
|
Re: Keypad Upgrade for Using Mach2
Dominique,
The keypads are not supposed to be sent with Mach2 mounts yet. However, Terri noted that she received hers. According to our records, you mount has not shipped yet. Before it ships, our
|
Dominique,
The keypads are not supposed to be sent with Mach2 mounts yet. However, Terri noted that she received hers. According to our records, you mount has not shipped yet. Before it ships, our
|
By
Marj Christen
·
#68871
·
|
|
Re: GTOCP4 Not powering up
Forgot to ask....
Is the power cable connected to the Pyramid with the correct polarity?
Is the Pyramid's current-limiting control set high enough to supply the current the mount needs?
--- mike
|
Forgot to ask....
Is the power cable connected to the Pyramid with the correct polarity?
Is the Pyramid's current-limiting control set high enough to supply the current the mount needs?
--- mike
|
By
Mike Dodd
·
#68870
·
|
