Rich, I’ve just completed the firmware upgrade to version 4.19 on my Macbook Pro without any issues at all using Windows 10 Pro on a Bootcamp partition (No Virtualisation). I further used a Prolific

After getting the keypad upgrade, I parked in Park III. The APCC 3d Scope view showed the mount upside down. I used the keypad to park in Park 1 and APCC showed the scope on the right side of the

Will do. I just talked to George and that is what he suggested. Don Anderson

You might try using a fresh download from our website just in case there was a problem with your original download. Clear Skies, Marj Christen Astro-Physics, Inc 11250 Forest Hills

Ok. I was just going to call you to discuss. I will try that. I am using a single port Keyspan that has worked well since I got it in 2009. I will try a reload and let you know how I make out. Hears

Don, Do a re-load of the firmware and see if that fixes the problem. Regards, George George Whitney Astro-Physics, Inc. Phone: 815-282-1513 Email: george@...

Richard, APCC and the AP V2 driver both have park positions called “Park Current Position”. It is the same as “Park 0” in the keypad. Resuming is from “Last Parked”.

Renan, Prolific chips will sometimes work to run most aspects of our mounts, but they do not work to load new firmware. I am not a computer savant and cannot explain why, but they just don’t

Rich, It has always been a rule of thumb that all firmware upgrades to the keypad must be done on a PC and not a Mac with a virtual machine. I do not know the computer tech reasons for this.

I used "678" for "three finger salute" and it worked fine. Peter ---In ap-gto@..., <fyrframe@...> wrote : I successfully installed the update. All seems well. A few minornotes. First, there are 9

Marj I downloaded and completed the upgrade to Ver 4.19. The upgrade went as per the instructions however something must have been corrupted during the process although all of the pop up windows and

I successfully installed the update. All seems well. A few minornotes. First, there are 9 COM ports to choose from and my Keyspan was using COM16.I changed the port in my Device Manager to COM1

I saw a few posts and also noted the recommendation by AP involving updating. I went through the issue of PL 2303 vs FTDI chipset based USB to serial adaptors a month ago when I replaced my old WIN 7

Thanks Marj. I successfully updated my keypad to version 4.19. I have not yet tested with the mount since the mount is put away in the closet due to bad weather. I used the exact same imaging setup to

Hi Ray, jobdone...working well! Yves De : ap-gto@... [mailto:ap-gto@...] Envoyé : lundi 18 janvier2016 21:17 À : ap-gto@... Objet : RE: [ap-gto] NewASCOM Driver v5.08.03 (Beta) and updated

Hi Yves, Thanks for tracking that down. I just fixed that and posted 5.08.04 (beta): http://www.gralak.com/apdriver Please let me know if you see any other issues, Thanks, -Ray Gralak Author of

APCC and the keypad are two separate programs that can be used to control the mount. Each of these programs has its own park positions. They are each calculated in similar fashion, but neither one of

Park 0 is not incorporated into the ASCOM driver or APCC at this time. Clear Skies, Marj Christen Astro-Physics, Inc 11250 Forest Hills Rd Machesney Park, IL 61115 Phone: 815-282-1513 Fax:

Please be sure that you read the top section entitled: Check these Before You Start http://www.astro-physics.com/tech_support/mounts/keypad_update/419/419.htm Clear Skies, Marj

Sorry for not bring clear. I meant will we be able to use features like park 0 and resume, from APCC. Richard