Seems very unlikely the mount is moving in Az, but it is remote so I cannot look at the holddowns. I did the plate solve from images at the meridian, at hour angles of +4 and -4. At +4 the camera

According to the features list for Nebulosity 4 (http://www.stark-labs.com/whatsnew3/whatsnew3.html): • Ability to use Nebulosity as it were an ASCOM Camera, so other programs can script and control

Yes, more camera control is in V3. Nebulosity support will probably get added but ASCOM camera support, which is already in the V3 beta, covers most cameras. -Ray Gralak Author of APCC (Astro-Physics

Ray, I haven't checked in a while but have you included more capture software for pempro? I don't use maxim or Astroart. Have you included nebulosity? I never use your software because of this

My Keypad upgrade to 4.19.2 was also successful. Slews from Park 1 and 4 worked and parking to Park 1, 3 and 4 also worked. Thanks for fixing it. Peter ---In ap-gto@..., <greg@...> wrote : Loaded

If they are genuine Prolific (not counterfeit) then it may work. Give it a try, no harm should happen and the worse it can happen is that it may not work. Good luck and let us know the

I'm new at this group[. I just purchased the GTO1100 directly from AP, and I just downloaded the new 4.19.2 for the keypad. I want to learn as much as possible from this group. Thanks, Salsauno

Hi Barry, Is it possible that the flip to the other side is actually changing the polar alignment because of a weight shift or because the mount to pier knobs are not tight enough? And you should

Hi, Ouch, all of them are Prolific :) I will give it a try after I replace the battery. Thanks, Maarten Op 21/01/2016 om 18:43 schreef

Oh no, you will have all sunshine and roses from now on. Guaranteed - but you must read the manual 3 times cover to cover, otherwise all bets are off. Rolando

Ray: I definitely had APCC tracking rate correction off. If you look at the end of my message, I did the test of turning tracking correction on, and it did a great job as indicated by PEMPRO showing

Loaded 4.19.2 successfully on an 1100GTO. Resumes, tracksand parks just fine for me. I'm now fully prepared for the blizzard. Thanks, Greg Piepol

You may have a greater chance of success for uploading to Keypad if you use USB-to-Serial adapter containing FTDI chip. Try to avoid Prolific chip. Peter ---In ap-gto@..., <chris1011@...> wrote

Yes, that will work. Rolando

Hi, The battery of my AP600E is empty leaving the database corrupted. If I remember correctly you need a PC with a real serial port to run the update program. Off course there are no PC's left with

The new version of "Instructions for Uploading V4.19 to Your Keypad" no longer has the option "Printable PDF Version of these Instructions" at the top of the page. If you implement this again,

Hi Barry, One thing also, you need to make sure that APCC's tracking rate correction is turned off when doing PEMPro polar alignment measurements. -Ray Gralak Author of APCC (Astro-Physics Command

Hi Ned, My first priority has been to support APCC and the AP V2 ASCOM driver, which has taken much of my free time but I am working on V3 as much as I can. Weather has been terrible here in northern

Hi Barry, consistent. altitude suggested I PEMPro can measure drift to about 1/20th of a pixel so it is very sensitive. So the first few things that this could be: * If you were using a heavy scope

What ever happened to PEMPro 3. I’m faithful user of 2. Looking forward to 3. Ned Smith N 34,53,38.13 W 85,28,17.10 Near Chattanooga, TN