Date   

Re: Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Cheng-Yang Tan
 

Tried freezing and boiling water, but I can't get it off. The problem is that I don't have the right tools to do this.

cytan


On Sunday, August 15, 2021, 01:28:58 PM CDT, Seb@stro <sebastiendore1@...> wrote:



Try heating the adapter with boiling water. 

I would actually try the opposite, putting it in the freezer so metal contracts and parts loosen...

Hope this helps.

Sébastien 


Groups.io Links:

You receive all messages sent to this group.
You automatically follow any topics you start or reply to.

View/Reply Online (#80030) | Reply To Group | Reply To Sender | Mute This Topic | New Topic
Your Subscription | Contact Group Owner | Unsubscribe [sebastiendore1@...]


AP V2 driver, move axis command help.

Andy Ermolli
 
Edited

I am having a weird issue with the AP V2 driver. Currently I use the version v5.21.01. The mount is a Mach1 GTOCP3 with the V chip and I am not using the hand controller. 
This happens with both SGP and NINA. If I connect the mount and I try to nudge the mount with the direction keys in either software the mount will not move at the requested speed. I think the software is issuing a move axis command to the mount. I have the move rate set at 5 degrees per second. 

When I push the button I see the custom tracking rate in the driver window change to 1195.7233, that is either in Dec or RA depending on which button I pushed. However the mount will only move in the requested direction at the sidereal speed instead of 1195.7233x.
If I move the mount using the buttons in the driver window, then it will move at the correct speed set in the driver window.

Since this happens with two different programs I think it may be related to the driver, unless I am missing something?
This has not been an issue so far but now I am unable to use the three point polar alignment routine in NINA because the mount does not move fast enough between points. It does it at the sidereal rate and that would take hours.

Maybe there is a setting int he driver that I am unaware of? Any help will be greatly appreciated.
Thank you!


Re: Serial to ethernet #WiFi

David Diaz
 

I’m trying to ‘hardwire’ the GTOCP3 to my wireless router so I don’t have to physically connect it to my NUC.  The NUC connects as a LAN and can wirelessly access my focuser and run a VNC wirelessly to my laptop.

If I put the NUC atop my OTA, I’d have to run a USB ‘up’ the OTA from the mount.

I don’t have $1200 for the CP4 upgrade at the moment.

It’s all about the wires, the bane of my existence 🔭😎

DD


Re: Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Cheng-Yang Tan
 

Good idea. It’s going into the freezer


Sent from Yahoo Mail for iPad

On Sunday, August 15, 2021, 1:28 PM, Seb@stro <sebastiendore1@...> wrote:


Try heating the adapter with boiling water. 

I would actually try the opposite, putting it in the freezer so metal contracts and parts loosen...

Hope this helps.

Sébastien 


Groups.io Links:

You receive all messages sent to this group.
You automatically follow any topics you start or reply to.

View/Reply Online (#80030) | Reply To Group | Reply To Sender | Mute This Topic | New Topic
Your Subscription | Contact Group Owner | Unsubscribe [sebastiendore1@...]


Re: Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Sébastien Doré
 


Try heating the adapter with boiling water. 

I would actually try the opposite, putting it in the freezer so metal contracts and parts loosen...

Hope this helps.

Sébastien 


Groups.io Links:

You receive all messages sent to this group.
You automatically follow any topics you start or reply to.

View/Reply Online (#80030) | Reply To Group | Reply To Sender | Mute This Topic | New Topic
Your Subscription | Contact Group Owner | Unsubscribe [sebastiendore1@...]

_._,_._,_
<IMG_1978.jpeg>


Re: Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Cheng-Yang Tan
 

The adapter (black part) is off so it'll not be marred. The threaded sleeve is stuck onto the CW shaft. I'm worried that I'll mar the exterior threads of the sleeve while trying to get it off.

But in the end, it may be that I'll need to get a new sleeve if I can actually get the sleeve off. 

I'll talk to my friends who actually know how to do this. I don't have too many tools at home because don't want to hurt myself :)


cytan

On Sunday, August 15, 2021, 12:39:17 PM CDT, Christopher Erickson <christopher.k.erickson@...> wrote:


And if you don't want to get the help of a machine shop, a rubber strap wrench and a bench vise with a couple small pieces of plywood in the jaws will probably help you get them apart without marring up the adapter.

When you get them apart, carefully clean the threads of both with a wire brush and a paper towel before re-lubing them and putting them back together. 

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com

On Sun, Aug 15, 2021 at 7:33 AM Christopher Erickson via groups.io <christopher.k.erickson=gmail.com@groups.io> wrote:
My guess is that there was a sliver or two of aluminum in the threads of the counterweight shaft and that is what got the shaft and the adapter bound up together. Cleaning those threads first with an old toothbrush or wire brush first might have helped.

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com

On Sun, Aug 15, 2021 at 7:28 AM Christopher Erickson via groups.io <christopher.k.erickson=gmail.com@groups.io> wrote:
Your friendly local machine shop will be able to deal with this without a problem.

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com

On Sun, Aug 15, 2021 at 7:11 AM Cheng-Yang Tan via groups.io <cytan299=yahoo.com@groups.io> wrote:
Hi guys,
   Well, there are some people in this Universe who are blessed with the talent of not being able to do anything mechanical -- I'm one of those. My fear of cross threading the CW shaft into the CW adapter has finally come true :( :



As I untwisted the shaft out of the adapter (cursing and swearing + tapping with mallet on a long hex driver inserted into a hole in the adapter), instead of the shaft coming off, the metal sleeve came off with the shaft :(

Any ideas about how I can remove the shaft from the adapter?

And the best part was that I had actually lubed the threads of CW shaft so that I wouldn't do this.

Ugghhh!!!!!

cytan

P.S. The good thing is that I still have the old version of the CW adapter and an extra CW shaft, so technically, the AP1100 is still fine.


Re: Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Don Anderson
 

It is not likely that the shaft and adapter are actually cross threaded. You would have know if that happened since you would not have been able to thread the shaft all the way in.
It is possible that there was some contamination on the threads of either the shaft or the adapter when you made the connection. Try heating the adapter with boiling water. That may
expand it enough to enable you to tap it loose with the mallet.
Hope this helps

Don Anderson


On Sunday, August 15, 2021, 11:11:59 a.m. MDT, Cheng-Yang Tan via groups.io <cytan299@...> wrote:


Hi guys,
   Well, there are some people in this Universe who are blessed with the talent of not being able to do anything mechanical -- I'm one of those. My fear of cross threading the CW shaft into the CW adapter has finally come true :( :



As I untwisted the shaft out of the adapter (cursing and swearing + tapping with mallet on a long hex driver inserted into a hole in the adapter), instead of the shaft coming off, the metal sleeve came off with the shaft :(

Any ideas about how I can remove the shaft from the adapter?

And the best part was that I had actually lubed the threads of CW shaft so that I wouldn't do this.

Ugghhh!!!!!

cytan

P.S. The good thing is that I still have the old version of the CW adapter and an extra CW shaft, so technically, the AP1100 is still fine.


Re: Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Christopher Erickson
 

And if you don't want to get the help of a machine shop, a rubber strap wrench and a bench vise with a couple small pieces of plywood in the jaws will probably help you get them apart without marring up the adapter.

When you get them apart, carefully clean the threads of both with a wire brush and a paper towel before re-lubing them and putting them back together. 

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com


On Sun, Aug 15, 2021 at 7:33 AM Christopher Erickson via groups.io <christopher.k.erickson=gmail.com@groups.io> wrote:
My guess is that there was a sliver or two of aluminum in the threads of the counterweight shaft and that is what got the shaft and the adapter bound up together. Cleaning those threads first with an old toothbrush or wire brush first might have helped.

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com

On Sun, Aug 15, 2021 at 7:28 AM Christopher Erickson via groups.io <christopher.k.erickson=gmail.com@groups.io> wrote:
Your friendly local machine shop will be able to deal with this without a problem.

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com

On Sun, Aug 15, 2021 at 7:11 AM Cheng-Yang Tan via groups.io <cytan299=yahoo.com@groups.io> wrote:
Hi guys,
   Well, there are some people in this Universe who are blessed with the talent of not being able to do anything mechanical -- I'm one of those. My fear of cross threading the CW shaft into the CW adapter has finally come true :( :



As I untwisted the shaft out of the adapter (cursing and swearing + tapping with mallet on a long hex driver inserted into a hole in the adapter), instead of the shaft coming off, the metal sleeve came off with the shaft :(

Any ideas about how I can remove the shaft from the adapter?

And the best part was that I had actually lubed the threads of CW shaft so that I wouldn't do this.

Ugghhh!!!!!

cytan

P.S. The good thing is that I still have the old version of the CW adapter and an extra CW shaft, so technically, the AP1100 is still fine.


Re: Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Christopher Erickson
 

My guess is that there was a sliver or two of aluminum in the threads of the counterweight shaft and that is what got the shaft and the adapter bound up together. Cleaning those threads first with an old toothbrush or wire brush first might have helped.

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com


On Sun, Aug 15, 2021 at 7:28 AM Christopher Erickson via groups.io <christopher.k.erickson=gmail.com@groups.io> wrote:
Your friendly local machine shop will be able to deal with this without a problem.

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com

On Sun, Aug 15, 2021 at 7:11 AM Cheng-Yang Tan via groups.io <cytan299=yahoo.com@groups.io> wrote:
Hi guys,
   Well, there are some people in this Universe who are blessed with the talent of not being able to do anything mechanical -- I'm one of those. My fear of cross threading the CW shaft into the CW adapter has finally come true :( :



As I untwisted the shaft out of the adapter (cursing and swearing + tapping with mallet on a long hex driver inserted into a hole in the adapter), instead of the shaft coming off, the metal sleeve came off with the shaft :(

Any ideas about how I can remove the shaft from the adapter?

And the best part was that I had actually lubed the threads of CW shaft so that I wouldn't do this.

Ugghhh!!!!!

cytan

P.S. The good thing is that I still have the old version of the CW adapter and an extra CW shaft, so technically, the AP1100 is still fine.


Re: Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Christopher Erickson
 

Your friendly local machine shop will be able to deal with this without a problem.

"My advice is always free and worth every penny!"

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com


On Sun, Aug 15, 2021 at 7:11 AM Cheng-Yang Tan via groups.io <cytan299=yahoo.com@groups.io> wrote:
Hi guys,
   Well, there are some people in this Universe who are blessed with the talent of not being able to do anything mechanical -- I'm one of those. My fear of cross threading the CW shaft into the CW adapter has finally come true :( :



As I untwisted the shaft out of the adapter (cursing and swearing + tapping with mallet on a long hex driver inserted into a hole in the adapter), instead of the shaft coming off, the metal sleeve came off with the shaft :(

Any ideas about how I can remove the shaft from the adapter?

And the best part was that I had actually lubed the threads of CW shaft so that I wouldn't do this.

Ugghhh!!!!!

cytan

P.S. The good thing is that I still have the old version of the CW adapter and an extra CW shaft, so technically, the AP1100 is still fine.


Re: Serial to ethernet #WiFi

Christopher Erickson
 

It *might* work. What problem are you trying to solve?

-Christopher Erickson
Observatory Engineer
Summit Kinetics
Waikoloa, Hawaii


Virus-free. www.avg.com


On Sun, Aug 15, 2021 at 2:10 AM David Diaz <night.skywatcher@...> wrote:
Hello
Is there any reason this
iTach TCP/IP to Serial (RS232) With Power Over Ethernet
would not work if I plugged the GTOCP3 serial connector into this device, and then to my portable, wireless router?

Thanks
DD


Ugghhh cross threaded CW shaft into CW shaft adapter with metal threaded sleeve

Cheng-Yang Tan
 

Hi guys,
   Well, there are some people in this Universe who are blessed with the talent of not being able to do anything mechanical -- I'm one of those. My fear of cross threading the CW shaft into the CW adapter has finally come true :( :



As I untwisted the shaft out of the adapter (cursing and swearing + tapping with mallet on a long hex driver inserted into a hole in the adapter), instead of the shaft coming off, the metal sleeve came off with the shaft :(

Any ideas about how I can remove the shaft from the adapter?

And the best part was that I had actually lubed the threads of CW shaft so that I wouldn't do this.

Ugghhh!!!!!

cytan

P.S. The good thing is that I still have the old version of the CW adapter and an extra CW shaft, so technically, the AP1100 is still fine.


Re: Serial to ethernet #WiFi

Sébastien Doré
 


Hi David,

3 things quickly come to my mind:

- While that’s not a reason for it « not to work », the PoE feature may be useless depending on if your router supports it or not (usually requires a beefy power supply) or if you plan to upgrade to one that supports it in the future. That company sells a similar model without PoE which is likely to be cheaper (I have not checked). Of course, for similar pricing, it is a nice to have.

- They don’t specify environmental operating conditions in the datasheet, so you might want to check with them if it is suited for outdoor (temperature range, high humidity, etc) or at least for likely conditions at your observing place/observatory.

- last, the Ethernet speed supported is 10/100 Mbps ONLY (no 1000 Mbps, ie 1Gbps) so make sure your router supports 10 or 100 (or both) otherwise it will NOT work (the underlying « protocol » is different for each speed).

Clear skies!
Sébastien 


Le 15 août 2021 à 08:10, David Diaz <night.skywatcher@...> a écrit :

Hello
Is there any reason this
iTach TCP/IP to Serial (RS232) With Power Over Ethernet
would not work if I plugged the GTOCP3 serial connector into this device, and then to my portable, wireless router?

Thanks
DD


Serial to ethernet #WiFi

David Diaz
 

Hello
Is there any reason this
iTach TCP/IP to Serial (RS232) With Power Over Ethernet
would not work if I plugged the GTOCP3 serial connector into this device, and then to my portable, wireless router?

Thanks
DD


Re: Mach1 1200x move rate with 5.30.10 driver

Andy Ermolli
 

Thank you Ray! I installed the version that you linked and all is working well now:)
Strange thing is that the 1200x rate worked fine with my cp4 1100 mount.

I have another issue with Nina and the mach1 but it could be related to the same driver problem. I will test tonight and may start a new thread.


Re: APCC virtual ports #APCC

ap@CaptivePhotons.com
 

Re USBDView - apologies, JoePetrick9, despite you saying "virtual" clearly, I was thinking USB ports, and didn't connect it until I saw Ray's answer.  This tool is worthless for the virtual ports created by APCC.   Save my note for the day you have a USB port/driver issue.   Apologies for the tangent. 


Re: APCC virtual ports #APCC

Ray Gralak
 

Hi Joe,

 

It's hard to say what resulted by disabling the virtual port. If you uninstall APCC it will uninstall the Eltima virtual port driver. Then when reinstalling APCC, make sure to enable the checkbox to install the Eltima virtual driver again. This should put the virtual ports in the default state.

 

Note: the virtual ports that APCC creates only exist while APCC is running, so you won't see them in Device Manager when APCC is not active.

 

And, normally, you won't need to manually create the virtual ports. APCC will automatically allocate appropriate port numbers. And APCC will configure the ASCOM driver if "Auto-Config" is enabled in the AP V2 Driver group box, as shown here:

 

 

-Ray

 

 

> -----Original Message-----

> From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of joepetrick9@...

> Sent: Saturday, August 14, 2021 8:18 AM

> To: main@ap-gto.groups.io

> Subject: [ap-gto] APCC virtual ports #APCC

>

> I disabled a virtual port in device manager on win 10 PC and now when i create ports in APCC it does create the

> ports in APCC but not in my device manager so I cannot connect to V2 . Does anyone know how i can enable

> virtual port i disabled. There is no port showing up in device manager so i cant enable it there. I have deleted and

> reloaded APCC and V2 and Ascom but no help . I have checked "enable virtual ports" when i reloaded APCC.

> Driving me nuts.   Thanks in advance Joe


Re: Mach1 1200x move rate with 5.30.10 driver

Ray Gralak
 

Hi Andy,

I think there is an issue setting the proper move rate with 5.30.10 with CP3's. Almost all of the changes in the 5.30.x versions were for the Mach 2 and GTOCP4. If it’s a problem you can fall back to v5.20.01 until a new driver version is released.

If you would like to go back to the older driver, here is the link. You don't need to uninstall 4.30.10. You can just run the 5.21.02 installer.

https://www.gralak.com/apdriver/AstroPhysics_V2_Setup_5.21.01.exe

-Ray

-----Original Message-----
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Andy Ermolli
Sent: Saturday, August 14, 2021 12:49 PM
To: main@ap-gto.groups.io
Subject: [ap-gto] Mach1 1200x move rate with 5.30.10 driver

Since I updated the Ascom driver to the version 5.30.10 I am unable to move the Mach1 GTOCP3 with V chip at
1200x using the buttons in the driver window.
The mount just won't move if I have 1200x selected.
If I select 600x, then I can move the mount but it moves at 1200x.
The 1200x works fine with the 1100. I have not tested it with the 900 yet.

Is it just me or are others having this issue?


Re: Mach 2 + 12.5" AGO iDK?

Bill Long
 

Yeah the impressive thing for me isn't just the scope, as the Mach 2 can easily handle that within specification. It was how loaded down the total system was, it's size, AND the total length of the system at critical focus. 68 lbs of gear at that size and total length is asking a lot.

No problem for the Mach 2 though. 


From: main@ap-gto.groups.io <main@ap-gto.groups.io> on behalf of J. Belden via groups.io <jjb4469@...>
Sent: Saturday, August 14, 2021 4:22 PM
To: main@ap-gto.groups.io <main@ap-gto.groups.io>
Subject: Re: [ap-gto] Mach 2 + 12.5" AGO iDK?
 
Back many years ago while waiting for my AP1100 mount, I had no issues imaging with my Mach 1 with my C14 black tube, so Im not really surprised that the Mach 2 can handle a 12.5” AGO and bigger.

Though, I ended up moving up to an AP1600 for my 12.5” AGO and 17” PW for my portable setup.  I might not have a collection of AP scopes but Im building my mount collection.  Still think the Mach 1 is the best looking one but my AP1600 AE is the best tracking mount that I have ever had bar none. 

Joe B






Re: Mach 2 + 12.5" AGO iDK?

J. Belden
 

Back many years ago while waiting for my AP1100 mount, I had no issues imaging with my Mach 1 with my C14 black tube, so Im not really surprised that the Mach 2 can handle a 12.5” AGO and bigger.

Though, I ended up moving up to an AP1600 for my 12.5” AGO and 17” PW for my portable setup. I might not have a collection of AP scopes but Im building my mount collection. Still think the Mach 1 is the best looking one but my AP1600 AE is the best tracking mount that I have ever had bar none.

Joe B

3361 - 3380 of 83330