Date   

Re: [ap-ug] Tiny Hourglass in a cosmic Lagoon

Pete Lardizabal
 

Stunning!

😎

Pete

On Jul 17, 2020, at 6:42 PM, Roland Christen via groups.io <chris1011@...> wrote:


Dive in, the water is warm:

https://www.astrobin.com/full/jqaood/0/?nc=Uncarollo&real=&mod=

Rolando


Lens Cleaner

Larry Phillips
 

Rolando, what is your opinion about the lens cleaner available from the following website?
 www.photoniccleaning.com 

Larry


Re: Of Mice and Mounts

W Hilmo
 

A couple of years ago, I broke down my AP1100 after it had been set up in the yard for a few months and covered when not in use.  Some enterprising creature had completely filled the inside of the mount with maple seeds.  No harm was done and all I needed to do was to separate the mount halves and lightly blow out the stuff that didn’t just fall out.

 

There was no evidence of a nest, just a food storehouse.

 

 

 

From: main@ap-gto.groups.io <main@ap-gto.groups.io> On Behalf Of uncarollo2 <chris1011@...> via groups.io
Sent: Friday, July 17, 2020 2:57 PM
To: main@ap-gto.groups.io
Subject: [ap-gto] Of Mice and Mounts

 

Lat week during an imaging session in my observatory I happened to see a mouse rappelling down the power cord on my nearby 1600 mount. Rather strange, I thought, that mice would use wires as highways up and down a telescope pier.

 

Then last night, as I was getting ready to do some imaging with the 17" astrograph on that 1600 mount, I ran into a familiar problem. The Dec axis ran for 1 second and stopped, with the yellow light coming on in the CP4 controller. I looked up the open hole in the back of the RA (yes I forgot to put the plug back in last August) and saw some shredded paper way up in the Dec axis cavity. I knew then I had to get into the Dec axis and check out the damage.

 

Since I had a large astrograph on the mount, I decided to put the mount counterweight down, scope on top and lock the axes clutch knobs tight. Without removing the scope, I removed all the counterweights, the counterweight shaft and unscrewed the counterweight adapter from the end of the Dec axis. Here's what it looked like:

 

 

After cleaning out the mess:

 

 

The mice had chewed on all the wires and broke several of them. Fortunately I have lots of practice soldering. I pulled out the Dec connector wire along with the crossover box:

 

 

The mice had damage 6 of the 8 wires. With some matching pieces of wire, some heat shrink tubing I spliced in the damaged portions:

 

 

Finished cable wrapped with some electrical tape. Did it work? YES, the mount is back in business and the scope is imaging again.

 


Re: Of Mice and Mounts

Roland Christen
 

Ouch, that musta hurt (in your pocketbook).

Rolando



-----Original Message-----
From: Cheng-Yang Tan via groups.io <cytan299@...>
To: main@ap-gto.groups.io
Sent: Fri, Jul 17, 2020 5:29 pm
Subject: Re: [ap-gto] Of Mice and Mounts

Hi Rolando,

Yep mice are a menace to equipment. I had mice make a home in one of my RF power amplifiers (~$75k each). They got in via the air cooling slots which were just small 1/2" wide slots. I didn't expect that mice could actually squeeze through them.  Unfortunately, due to the mice pee and cr*p, this amplifer was a health hazard for anyone to repair and clean it and so it had to be written off. I still know where the power amp carcass is ...

For its replacement, I had the techs install chicken wire to cover the holes.

Hopefully, you found the nest dry and could clean it properly.

cytan


On Friday, July 17, 2020, 04:58:45 PM CDT, uncarollo2 <chris1011@...> wrote:


Lat week during an imaging session in my observatory I happened to see a mouse rappelling down the power cord on my nearby 1600 mount. Rather strange, I thought, that mice would use wires as highways up and down a telescope pier.

Then last night, as I was getting ready to do some imaging with the 17" astrograph on that 1600 mount, I ran into a familiar problem. The Dec axis ran for 1 second and stopped, with the yellow light coming on in the CP4 controller. I looked up the open hole in the back of the RA (yes I forgot to put the plug back in last August) and saw some shredded paper way up in the Dec axis cavity. I knew then I had to get into the Dec axis and check out the damage.

Since I had a large astrograph on the mount, I decided to put the mount counterweight down, scope on top and lock the axes clutch knobs tight. Without removing the scope, I removed all the counterweights, the counterweight shaft and unscrewed the counterweight adapter from the end of the Dec axis. Here's what it looked like:



After cleaning out the mess:



The mice had chewed on all the wires and broke several of them. Fortunately I have lots of practice soldering. I pulled out the Dec connector wire along with the crossover box:



The mice had damage 6 of the 8 wires. With some matching pieces of wire, some heat shrink tubing I spliced in the damaged portions:



Finished cable wrapped with some electrical tape. Did it work? YES, the mount is back in business and the scope is imaging again.



Re: Of Mice and Mounts

Steven
 

Mice can get into any space larger than the diameter of a pencil. Holes must be smaller than a pencil width to prevent mice entering. Not too sure about chicken wire working out for you.

SE


From: main@ap-gto.groups.io <main@ap-gto.groups.io> on behalf of Cheng-Yang Tan via groups.io <cytan299@...>
Sent: Friday, 17 July 2020 6:29 PM
To: main@ap-gto.groups.io <main@ap-gto.groups.io>
Subject: Re: [ap-gto] Of Mice and Mounts
 
Hi Rolando,

Yep mice are a menace to equipment. I had mice make a home in one of my RF power amplifiers (~$75k each). They got in via the air cooling slots which were just small 1/2" wide slots. I didn't expect that mice could actually squeeze through them.  Unfortunately, due to the mice pee and cr*p, this amplifer was a health hazard for anyone to repair and clean it and so it had to be written off. I still know where the power amp carcass is ...

For its replacement, I had the techs install chicken wire to cover the holes.

Hopefully, you found the nest dry and could clean it properly.

cytan


On Friday, July 17, 2020, 04:58:45 PM CDT, uncarollo2 <chris1011@...> wrote:


Lat week during an imaging session in my observatory I happened to see a mouse rappelling down the power cord on my nearby 1600 mount. Rather strange, I thought, that mice would use wires as highways up and down a telescope pier.

Then last night, as I was getting ready to do some imaging with the 17" astrograph on that 1600 mount, I ran into a familiar problem. The Dec axis ran for 1 second and stopped, with the yellow light coming on in the CP4 controller. I looked up the open hole in the back of the RA (yes I forgot to put the plug back in last August) and saw some shredded paper way up in the Dec axis cavity. I knew then I had to get into the Dec axis and check out the damage.

Since I had a large astrograph on the mount, I decided to put the mount counterweight down, scope on top and lock the axes clutch knobs tight. Without removing the scope, I removed all the counterweights, the counterweight shaft and unscrewed the counterweight adapter from the end of the Dec axis. Here's what it looked like:



After cleaning out the mess:



The mice had chewed on all the wires and broke several of them. Fortunately I have lots of practice soldering. I pulled out the Dec connector wire along with the crossover box:



The mice had damage 6 of the 8 wires. With some matching pieces of wire, some heat shrink tubing I spliced in the damaged portions:



Finished cable wrapped with some electrical tape. Did it work? YES, the mount is back in business and the scope is imaging again.



Tiny Hourglass in a cosmic Lagoon

Roland Christen
 

Dive in, the water is warm:

https://www.astrobin.com/full/jqaood/0/?nc=Uncarollo&real=&mod=

Rolando


Re: Of Mice and Mounts

Cheng-Yang Tan
 

Hi Rolando,

Yep mice are a menace to equipment. I had mice make a home in one of my RF power amplifiers (~$75k each). They got in via the air cooling slots which were just small 1/2" wide slots. I didn't expect that mice could actually squeeze through them.  Unfortunately, due to the mice pee and cr*p, this amplifer was a health hazard for anyone to repair and clean it and so it had to be written off. I still know where the power amp carcass is ...

For its replacement, I had the techs install chicken wire to cover the holes.

Hopefully, you found the nest dry and could clean it properly.

cytan


On Friday, July 17, 2020, 04:58:45 PM CDT, uncarollo2 <chris1011@...> wrote:


Lat week during an imaging session in my observatory I happened to see a mouse rappelling down the power cord on my nearby 1600 mount. Rather strange, I thought, that mice would use wires as highways up and down a telescope pier.

Then last night, as I was getting ready to do some imaging with the 17" astrograph on that 1600 mount, I ran into a familiar problem. The Dec axis ran for 1 second and stopped, with the yellow light coming on in the CP4 controller. I looked up the open hole in the back of the RA (yes I forgot to put the plug back in last August) and saw some shredded paper way up in the Dec axis cavity. I knew then I had to get into the Dec axis and check out the damage.

Since I had a large astrograph on the mount, I decided to put the mount counterweight down, scope on top and lock the axes clutch knobs tight. Without removing the scope, I removed all the counterweights, the counterweight shaft and unscrewed the counterweight adapter from the end of the Dec axis. Here's what it looked like:



After cleaning out the mess:



The mice had chewed on all the wires and broke several of them. Fortunately I have lots of practice soldering. I pulled out the Dec connector wire along with the crossover box:



The mice had damage 6 of the 8 wires. With some matching pieces of wire, some heat shrink tubing I spliced in the damaged portions:



Finished cable wrapped with some electrical tape. Did it work? YES, the mount is back in business and the scope is imaging again.



Re: Of Mice and Mounts

thefamily90 Phillips
 

Wow!!

Jim


From: main@ap-gto.groups.io <main@ap-gto.groups.io> on behalf of uncarollo2 <chris1011@...> via groups.io <chris1011@...>
Sent: Friday, July 17, 2020 7:57 PM
To: main@ap-gto.groups.io <main@ap-gto.groups.io>
Subject: [ap-gto] Of Mice and Mounts
 
Lat week during an imaging session in my observatory I happened to see a mouse rappelling down the power cord on my nearby 1600 mount. Rather strange, I thought, that mice would use wires as highways up and down a telescope pier.

Then last night, as I was getting ready to do some imaging with the 17" astrograph on that 1600 mount, I ran into a familiar problem. The Dec axis ran for 1 second and stopped, with the yellow light coming on in the CP4 controller. I looked up the open hole in the back of the RA (yes I forgot to put the plug back in last August) and saw some shredded paper way up in the Dec axis cavity. I knew then I had to get into the Dec axis and check out the damage.

Since I had a large astrograph on the mount, I decided to put the mount counterweight down, scope on top and lock the axes clutch knobs tight. Without removing the scope, I removed all the counterweights, the counterweight shaft and unscrewed the counterweight adapter from the end of the Dec axis. Here's what it looked like:


After cleaning out the mess:


The mice had chewed on all the wires and broke several of them. Fortunately I have lots of practice soldering. I pulled out the Dec connector wire along with the crossover box:


The mice had damage 6 of the 8 wires. With some matching pieces of wire, some heat shrink tubing I spliced in the damaged portions:


Finished cable wrapped with some electrical tape. Did it work? YES, the mount is back in business and the scope is imaging again.


Of Mice and Mounts

Roland Christen
 

Lat week during an imaging session in my observatory I happened to see a mouse rappelling down the power cord on my nearby 1600 mount. Rather strange, I thought, that mice would use wires as highways up and down a telescope pier.

Then last night, as I was getting ready to do some imaging with the 17" astrograph on that 1600 mount, I ran into a familiar problem. The Dec axis ran for 1 second and stopped, with the yellow light coming on in the CP4 controller. I looked up the open hole in the back of the RA (yes I forgot to put the plug back in last August) and saw some shredded paper way up in the Dec axis cavity. I knew then I had to get into the Dec axis and check out the damage.

Since I had a large astrograph on the mount, I decided to put the mount counterweight down, scope on top and lock the axes clutch knobs tight. Without removing the scope, I removed all the counterweights, the counterweight shaft and unscrewed the counterweight adapter from the end of the Dec axis. Here's what it looked like:


After cleaning out the mess:


The mice had chewed on all the wires and broke several of them. Fortunately I have lots of practice soldering. I pulled out the Dec connector wire along with the crossover box:


The mice had damage 6 of the 8 wires. With some matching pieces of wire, some heat shrink tubing I spliced in the damaged portions:


Finished cable wrapped with some electrical tape. Did it work? YES, the mount is back in business and the scope is imaging again.


Re: PlateSolve2 vs. TheSkyX Image Link for APPM Point Mapping

Stuart <stuart.j.heggie@...>
 

Probably you just need to start up TSX in Administrative mode, shut it down and restart normally. 

Stuart 

On Fri, Jul 17, 2020 at 4:13 PM Dean Jacobsen <deanjacobsen@...> wrote:
So, an update.

After starting over as per Ray's SGP/PlateSolve2 tutorial, I have it working again and have been enjoying the goodness of imaging without a guide scope.

The Mach2 is working perfectly.

I did try to get TheSkyX working as my plate solver first and kept getting a message about not being able to start an ActiveX element or session or whatever.  I will take a screen shot of the error message next time I go out in a few days.
--
Dean Jacobsen
http://astrophoto.net/wp/
Image Gallery - http://astrophoto.net/wp/image-gallery/
Astrobin - https://www.astrobin.com/users/deanjacobsen/ 

--

--

Stuart
http://www.astrofoto.ca/stuartheggie/


Re: PlateSolve2 vs. TheSkyX Image Link for APPM Point Mapping

Dean Jacobsen
 

So, an update.

After starting over as per Ray's SGP/PlateSolve2 tutorial, I have it working again and have been enjoying the goodness of imaging without a guide scope.

The Mach2 is working perfectly.

I did try to get TheSkyX working as my plate solver first and kept getting a message about not being able to start an ActiveX element or session or whatever.  I will take a screen shot of the error message next time I go out in a few days.
--
Dean Jacobsen
http://astrophoto.net/wp/
Image Gallery - http://astrophoto.net/wp/image-gallery/
Astrobin - https://www.astrobin.com/users/deanjacobsen/ 


Re: Changing Keypad battery

George
 

Geoff,

 

Please reference our Tech Support page.

https://astro-physics.info/tech_support/mounts/keypad/keypad-maintenance-instructions.pdf

 

Regards,

 

George

 

George Whitney

Astro-Physics, Inc.

Phone:  815-222-6538 (direct line)

Phone:  815-282-1513 (office)

Email:  george@...

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Geoff Smith
Sent: Thursday, July 16, 2020 8:32 PM
To: main@ap-gto.groups.io
Subject: [ap-gto] Changing Keypad battery

 

This is probably going to be a "doh" moment, but I am puzzled by the following line on P11 of the keypad maintenance manual

"Unplug the lithium battery connector. Note the Real Time Clock (RTC ) Module. This is NOT the battery!! Do NOT attempt
to remove this! (See photo top of following page)"

What is the lithium battery connector and how do I unplug it?
Geoff


Re: Issue with starting ASCOM driver from SGP #ASCOM_V2_Driver

Ray Gralak
 

Hi Paul,

The issue is repeatable i.e. it happens every time I try to connect from SGP.
1. Make sure that you are not starting APCC "as Administrator". You do not need to run APCC with admin privileges.
2. Make sure that you are not starting SGP "as administrator". That will start a second instance of the driver when SGP connects to the AP V2 driver.
3. Enable the "Auto-Config" option in the "AP V2 Driver" group box in APCC. This will always reconfigure the AP V2 driver even if APCC's virtual com ports change.

-Ray Gralak
Author of APCC (Astro-Physics Command Center): https://www.astro-physics.com/apcc-pro
Author of PEMPro V3: https://www.ccdware.com
Author of Astro-Physics V2 ASCOM Driver: https://www.siriusimaging.com/apdriver


-----Original Message-----
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of DiscoDuck
Sent: Thursday, July 16, 2020 9:10 PM
To: main@ap-gto.groups.io
Subject: [ap-gto] Issue with starting ASCOM driver from SGP #ASCOM_V2_Driver

This may well be an SGP issue, but let me ask here just in case anyone has seen this ... or hopefully Ray might
have some insight.

I have an issue where
- I start APCC and connect it to the mount and initialise the mount
- I start SGP
- I click on connect to mount in SGP

Normally, this fires up the AP ASCOM driver, which connects to APCC (virtual com port) and all is good. However,
it now brings up the ASCOM driver with "default values" and you can see it flashing while trying to connect to
APCC and then eventually fails and the ASCOM driver disappears and I get an error message from SGP that the
mount failed to connect. It has previously worked fine [though I have had this issue before and it went away when
I reinstalled the ASCOM driver. Could do that again now, but thought since it has resurfaced it is worth asking]

The issue is repeatable i.e. it happens every time I try to connect from SGP.

Current workaround is to connect to the ASCOM driver from APCC. Then when I click connect from SGP it simply
connects to the (already running and initialised) ASCOM driver and all is good.

Ideas/comments appreciated.
Thanks,
Paul


Re: Changing Keypad battery

Geoff Smith
 

Thanks Konstantin. That figures.
I’ll look into doing that.


Re: Changing Keypad battery

Konstantin von Poschinger
 

Hi,

You have to reload the database.

Grüsse

Konstantin v. Poschinger


Hammerichstr. 5
22605 Hamburg
040/8805747
0171/1983476

Am 17.07.2020 um 09:05 schrieb Geoff Smith <ghsmith45@...>:

Ok, I misread one of the later instructions and thought there were two battery connectors that had to be removed. 
I installed a new battery, but the data base refuses to point properly, so I still have a problem.


Re: Changing Keypad battery

Geoff Smith
 

Ok, I misread one of the later instructions and thought there were two battery connectors that had to be removed. 
I installed a new battery, but the data base refuses to point properly, so I still have a problem.


Re: Issue with starting ASCOM driver from SGP #ASCOM_V2_Driver

DiscoDuck
 

Thanks. My understanding is that APCC talks directly to the mount, and the ASCOM driver sits above APCC and the apps (SGP) talk to that. I haven't got APCC configured to auto-start the driver (I think you can). But it is odd that starting it from SGP used to work and now doesn't. Thanks for your comments though.


Re: Issue with starting ASCOM driver from SGP #ASCOM_V2_Driver

Worsel
 

Paul

When I start up APCC the driver ALWAYS starts automatically...I think the driver MUST start to connect to the mount.  I never have to start the driver on its own. I am unsure why this does not seem to happen for your config.  Ray Gralak likely has more insight.

Bryan


Re: Changing Keypad battery

Geoff Smith
 

So is the lithium battery connector just the white plug with the blue and yellow wires? 


Issue with starting ASCOM driver from SGP #ASCOM_V2_Driver

DiscoDuck
 

This may well be an SGP issue, but let me ask here just in case anyone has seen this ... or hopefully Ray might have some insight.

I have an issue where
- I start APCC and connect it to the mount and initialise the mount
- I start SGP
- I click on connect to mount in SGP

Normally, this fires up the AP ASCOM driver, which connects to APCC (virtual com port) and all is good. However, it now brings up the ASCOM driver with "default values" and you can see it flashing while trying to connect to APCC and then eventually fails and the ASCOM driver disappears and I get an error message from SGP that the mount failed to connect. It has previously worked fine [though I have had this issue before and it went away when I reinstalled the ASCOM driver. Could do that again now, but thought since it has resurfaced it is worth asking]

The issue is repeatable i.e. it happens every time I try to connect from SGP.

Current workaround is to connect to the ASCOM driver from APCC. Then when I click connect from SGP it simply connects to the (already running and initialised) ASCOM driver and all is good.

Ideas/comments appreciated.
Thanks,
Paul

7401 - 7420 of 79096