Date   

Re: Mach1 - regreasing

Cheng-Yang Tan
 

Hi Karen,
   Thanks for the photos and the instructions! It really helps us klutz's (or the cut twice measure once guys :) )

cytan

On Tuesday, June 16, 2020, 02:34:13 PM CDT, Karen Christen <karen@...> wrote:


Hi Fernando,

 

I’ve attached directions to remove the auto-adjusting gearbox that you have on your Mach1.  Once you have the gearbox off you may proceed with re-greasing.

Karen Christen

Astro-Physics

 

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of uncarollo2 <chris1011@...> via groups.io
Sent: Tuesday, June 16, 2020 2:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 - regreasing

 

You have the latest gearbox. Karen will send you instructions how to disassemble it.

 

Rolando

 

 

 

-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 1:52 pm
Subject: Re: [ap-gto] Mach1 - regreasing

Hi Rolando,

 

Photos attached, thanks, Fernando

 

Em ter., 16 de jun. de 2020 às 11:06, uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> escreveu:

Can you send a picture of your mount's gearbox from 2 sides so we can see which model you have?

 

Rolando

 

 

 

-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 8:53 am
Subject: [ap-gto] Mach1 - regreasing

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando


--
Karen Christen
Astro-Physics


Re: Mach1 - regreasing

Karen Christen
 

Hi Fernando,

 

I’ve attached directions to remove the auto-adjusting gearbox that you have on your Mach1.  Once you have the gearbox off you may proceed with re-greasing.

Karen Christen

Astro-Physics

 

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of uncarollo2 <chris1011@...> via groups.io
Sent: Tuesday, June 16, 2020 2:33 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Mach1 - regreasing

 

You have the latest gearbox. Karen will send you instructions how to disassemble it.

 

Rolando

 

 

 

-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 1:52 pm
Subject: Re: [ap-gto] Mach1 - regreasing

Hi Rolando,

 

Photos attached, thanks, Fernando

 

Em ter., 16 de jun. de 2020 às 11:06, uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> escreveu:

Can you send a picture of your mount's gearbox from 2 sides so we can see which model you have?

 

Rolando

 

 

 

-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 8:53 am
Subject: [ap-gto] Mach1 - regreasing

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando


--
Karen Christen
Astro-Physics


Re: Mach1 - regreasing

Roland Christen
 

You have the latest gearbox. Karen will send you instructions how to disassemble it.

Rolando



-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 1:52 pm
Subject: Re: [ap-gto] Mach1 - regreasing

Hi Rolando,

Photos attached, thanks, Fernando

Em ter., 16 de jun. de 2020 às 11:06, uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> escreveu:
Can you send a picture of your mount's gearbox from 2 sides so we can see which model you have?

Rolando



-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 8:53 am
Subject: [ap-gto] Mach1 - regreasing

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando



Re: Mach1 - regreasing

Roland Christen
 

Those fasteners are not for adjustment.

I posted a series of photos just 2 days ago how to disassemble the gearbox. I will post them again.

Rolando



-----Original Message-----
From: Michael Hambrick via groups.io <mike.hambrick@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 1:59 pm
Subject: Re: [ap-gto] Mach1 - regreasing

Hi Fernando

Those are tamper proof fasteners in photos 1 and 2. Hopefully you will not have to deal with those. If so, I am not sure where you would find a hex wrench to loosen them in Brazil.


Best Regards

Michael Hambrick
ARLANXEO
TSR Global Manufacturing Support
PO Box 2000
Orange, TX 77631-2000
Phone: +1 (409) 882-2799
email: mike.hambrick@...


Re: Mach1 - regreasing

Roland Christen
 




-----Original Message-----
From: Michael Hambrick via groups.io <mike.hambrick@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 1:59 pm
Subject: Re: [ap-gto] Mach1 - regreasing

Hi Fernando

Those are tamper proof fasteners in photos 1 and 2. Hopefully you will not have to deal with those. If so, I am not sure where you would find a hex wrench to loosen them in Brazil.


Best Regards

Michael Hambrick
ARLANXEO
TSR Global Manufacturing Support
PO Box 2000
Orange, TX 77631-2000
Phone: +1 (409) 882-2799
email: mike.hambrick@...


Re: Mach1 - regreasing

Michael Hambrick <mike.hambrick@...>
 

Hi Fernando

Those are tamper proof fasteners in photos 1 and 2. Hopefully you will not have to deal with those. If so, I am not sure where you would find a hex wrench to loosen them in Brazil.


Best Regards

Michael Hambrick
ARLANXEO
TSR Global Manufacturing Support
PO Box 2000
Orange, TX 77631-2000
Phone: +1 (409) 882-2799
email: mike.hambrick@...


Re: Mach1 - regreasing

Fernando Proietti
 

Hi Rolando,

Photos attached, thanks, Fernando

Em ter., 16 de jun. de 2020 às 11:06, uncarollo2 <chris1011@...> via groups.io <chris1011=aol.com@groups.io> escreveu:

Can you send a picture of your mount's gearbox from 2 sides so we can see which model you have?

Rolando



-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 8:53 am
Subject: [ap-gto] Mach1 - regreasing

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando



Re: help with AP900 guiding via ASIAir Pro

Dean Jacobsen
 

Steve,

Ray said that your driver logs report an "E" chip in your CP2 controller.

You said that the seller told you that he had upgraded the chip to a CP4 chip but Roland said that there was no such thing as a CP4 chip for your controller.

It might be worth your time to open up the controller box and see what is actually in there.  If I recall correctly the chip version is printed on the surface.
--
Dean Jacobsen
http://astrophoto.net/wp/ 
Image Gallery - http://astrophoto.net/wp/image-gallery/
Astrobin - https://www.astrobin.com/users/deanjacobsen/ 


Re: help with AP900 guiding via ASIAir Pro

sgbonnell@...
 

p.s. your description of the problem seems to match last night's observations on mount behaviour..

I had previously thought that somehow the tracking was being disabled on the mount when guiding was initiated, but I think it is more likely that the mount is executing an open looped move per your explanation above.
When I deliberately turn off tracking, the stars trail in the OPPOSITE direction to what I had been seeing previously when trying to guide. 
So it is not that tracking is disabled, rather being overridden by open Move command.. 
Steve


Re: help with AP900 guiding via ASIAir Pro

sgbonnell@...
 

Hi Ray,
I think I originally had CP2 specified in the mount set up and had changed it to CP4 trying to debug the problem...
But to be sure, I'll reset the driver to CP2 & AP900 and give it a try tonight..
thanks for taking a look at the logs...
cheers,
Steve


Re: Point Mapping Strategies for the Mobile Imager

Dean Jacobsen
 

On Sun, Jun 14, 2020 at 09:35 PM, Dean Jacobsen wrote:



 
Still looking for opinions regarding success or cautions regarding point mapping runs which are specific to the path a particular target will take during the course of a night.  If a scheme like this works then it would be helpful for those of us who setup and take down their rigs nightly.
--
Dean Jacobsen
http://astrophoto.net/wp/ 
Image Gallery - http://astrophoto.net/wp/image-gallery/
Astrobin - https://www.astrobin.com/users/deanjacobsen/ 


Re: help with AP900 guiding via ASIAir Pro

Ray Gralak
 

Hi Steve,

I see the problem. The old firmware that you have (Rev 'E' chip) requires separate start and stop commands to issue guider moves, but the driver is sending timed moves. Timed moves handle starting (and stopping a guider move after the supplied duration value) from within the control box.

However, I think the old firmware in your mount is handling this as a simple start move and the move continues while waiting for a stop command. Since the driver expects the control box to stop the move after the supplied duration, the driver does not send a stop move command. Thus, the GTOCP2 firmware keeps the guider move going until you stopped it with an appropriate key press on the keypad.

I think you should be able to fix this problem by selecting the correct mount type and controller in the AP V2 driver setup. That is, make sure you have AP900 as the mount type and GTOCP2 as the controller. In one of your logs you have GTOCP4 selected as the controller and no mount type. This will cause the driver to potentially send commands that the GTOCP2 will not understand, like the timed moves.

-Ray Gralak
Author of APCC (Astro-Physics Command Center): https://www.astro-physics.com/apcc-pro
Author of PEMPro V3: https://www.ccdware.com
Author of Astro-Physics V2 ASCOM Driver: https://www.siriusimaging.com/apdriver

-----Original Message-----
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of sgbonnell@outlook.com
Sent: Tuesday, June 16, 2020 7:07 AM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] help with AP900 guiding via ASIAir Pro

Hi Ray,
ASCOM driver logs attached...thanks!
Steve


Re: APCC and APPM is amazing

 

Just to close that out, we believe the reflections are caused by a missing baffle around the main mirror on the planewave cdk17. very unusual this happened, but a fix is in the works

Brian

On Tue, Jun 16, 2020 at 7:44 AM myrussellm via groups.io <mikerussell63=protonmail.com@groups.io> wrote:
Barry

Apologies, replied to the wrong post - the other image was with a planewave scope having six reflections in the image

Cheers

Mike 



--
Brian 



Brian Valente


Re: APCC and APPM is amazing

myrussellm
 

Barry

Apologies, replied to the wrong post - the other image was with a planewave scope having six reflections in the image

Cheers

Mike 


Re: help with AP900 guiding via ASIAir Pro

sgbonnell@...
 

Hi Ray,
ASCOM driver logs attached...thanks!
Steve


Re: Mach1 - regreasing

Roland Christen
 

Can you send a picture of your mount's gearbox from 2 sides so we can see which model you have?

Rolando



-----Original Message-----
From: Fernando Proietti <fernandoaproietti@...>
To: main@ap-gto.groups.io
Sent: Tue, Jun 16, 2020 8:53 am
Subject: [ap-gto] Mach1 - regreasing

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando



Mach1 - regreasing

Fernando Proietti
 

Dear all,

* My mount is outside the US, in Brasil;
* I am in Medicine/Public Health and with almost any mechanical skills;
* If I mess up anything while fixing, greasing, it is quite expensive to send the mount to AstroPhysics in the US. Have to say that George is always there when I need any help/information. Thanks George!
* English is not my native language and I have to look for the meaning of "spur gears", "axle shoulder bolts" :)))) Not a big deal, though.

So, maybe is only me, but I would be really grateful if someone out there (or someone from AstroPhysics) could put out there a video (or pictures) on how to remove the motor gear box and reinstall (Mach1). I am aware of a video on how to grease. But not on how to access the worn and worm Wheel gears.

Regards, Fernando



Re: help with AP900 guiding via ASIAir Pro

Ray Gralak
 

Yes, found the Cal file - I've attached. The guide star is lost at the start of Cal, so Cal does not get
completed.
Can you also post the AP V2 ASCOM driver log file so that we can see what the driver was doing?

-Ray Gralak
Author of APCC (Astro-Physics Command Center): https://www.astro-physics.com/apcc-pro
Author of PEMPro V3: https://www.ccdware.com
Author of Astro-Physics V2 ASCOM Driver: https://www.siriusimaging.com/apdriver


-----Original Message-----
From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of sgbonnell@outlook.com
Sent: Monday, June 15, 2020 11:15 AM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] help with AP900 guiding via ASIAir Pro

Yes, found the Cal file - I've attached. The guide star is lost at the start of Cal, so Cal does not get
completed.

When using PHD2 for guiding, I have the mount connected directly to my PC via the RS232 to USB cable.
Same set up when using ASIAir...USB end of the cable is plugged into the USB port on the ASIAir.
I just recently downloaded the latest A-P ASCOM driver from Ray G....my mount was a GTO2, but has been
upgraded to GTO4.

I have been using this same set up until recently on my Celestron CGX-L with no issues...it was only when I
started using ASIAir or PHD2 on the AP900 that I have had this issue..


Re: Sky Safari with Mach2

Christopher Erickson
 

Until they get over themselves and add Park3, I have given up on SkySafari too.

I have been asking them for Park3 for YEARS. 

-Christopher Erickson
Observatory engineer
Waikoloa, HI 96738
www.summitkinetics.com
   


On Mon, Jun 15, 2020, 7:16 PM Donald Rudny <mkea13800@...> wrote:
Hi All,

I just gave up on SkySafari and switched to Luminos.  I had to use APCC to initialize to P3.  Luminos lets you initialize in any position and has more controls of the mount like slewing and tracking rates.  I control everything with my iPad and Luminos.  No keypad.  
For $29.95 for Luminos and a smartphone or tablet you have your keypad.  I loved SkySafari, but their failure to provide more positions for initialization on AP mounts lost me as a supporter.

Don Rudny
Pepeekeo, Hi

On Jun 15, 2020, at 6:57 PM, Christopher Erickson <christopher.k.erickson@...> wrote:


PUH-LEEZE ask them to add Park3 too...


-Christopher Erickson
Observatory engineer
Waikoloa, HI 96738
www.summitkinetics.com
   

On Mon, Jun 15, 2020, 6:27 PM Marj Christen <marj@...> wrote:

We are working with Simulation Curriculum.

 

Clear Skies,

 

Marj Christen

Astro-Physics, Inc

11250 Forest Hills Rd

Machesney Park, IL 61115

Phone: 815-282-0910

Fax: 815-282-9847

www.astro-physics.com

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Dominique Durand via groups.io
Sent: Monday, June 15, 2020 12:02 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

On Mon, Jun 15, 2020 at 03:27 PM, Terri Zittritsch wrote:

Thanks Dominique, have you gotten any feedback from A-P or Simulation Curriculum?    I was wondering if it's normal, per past correspondence I've read about needing some initialization.  I know Sky Safari has a switch to pass time/location, but not sure that this does the trick.  I guess I'll wait to hear.  
I am an early adopter of Sky Safari and had every version since the beginning..  it is my favorite sky mapping program so hope that it'll be usable on the Mach2.    Maybe after getting the hand control sw.

Hi Terri,
I still have a doubt about this case that I had detected, because with my mach1 GTOCP4 that I had before I always had the keypad plugged in and I think that (Like the PC) was enough for Skysafari to synchronize, with my Mach1 GTOCP3 which I still have I pass for the WIFI by SkyFi3, that works for skysafari but there also I have a connected keypad.
My biggest concern and that I did not have with my GTOCP4 is that the WIFI network of the GTOCP5 disappears when the GTOCP5 is plugged into the PC, a problem linked to the USB3 sockets of my PC, because I plug into a USB2 socket it works .


Re: Sky Safari with Mach2

Woody Schlom
 

Good luck on that!  SkySafari hasn’t been the same since they sold out to Simulation Curriculum.  It’s still a great APP and I use it all the time, but support and feature requests have kind of gone down the toilet.

 

Woody

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Christopher Erickson
Sent: Monday, June 15, 2020 9:57 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

PUH-LEEZE ask them to add Park3 too...


-Christopher Erickson
Observatory engineer
Waikoloa, HI 96738
www.summitkinetics.com
   

 

On Mon, Jun 15, 2020, 6:27 PM Marj Christen <marj@...> wrote:

We are working with Simulation Curriculum.

 

Clear Skies,

 

Marj Christen

Astro-Physics, Inc

11250 Forest Hills Rd

Machesney Park, IL 61115

Phone: 815-282-0910

Fax: 815-282-9847

www.astro-physics.com

 

From: main@ap-gto.groups.io [mailto:main@ap-gto.groups.io] On Behalf Of Dominique Durand via groups.io
Sent: Monday, June 15, 2020 12:02 PM
To: main@ap-gto.groups.io
Subject: Re: [ap-gto] Sky Safari with Mach2

 

On Mon, Jun 15, 2020 at 03:27 PM, Terri Zittritsch wrote:

Thanks Dominique, have you gotten any feedback from A-P or Simulation Curriculum?    I was wondering if it's normal, per past correspondence I've read about needing some initialization.  I know Sky Safari has a switch to pass time/location, but not sure that this does the trick.  I guess I'll wait to hear.  
I am an early adopter of Sky Safari and had every version since the beginning..  it is my favorite sky mapping program so hope that it'll be usable on the Mach2.    Maybe after getting the hand control sw.

Hi Terri,
I still have a doubt about this case that I had detected, because with my mach1 GTOCP4 that I had before I always had the keypad plugged in and I think that (Like the PC) was enough for Skysafari to synchronize, with my Mach1 GTOCP3 which I still have I pass for the WIFI by SkyFi3, that works for skysafari but there also I have a connected keypad.
My biggest concern and that I did not have with my GTOCP4 is that the WIFI network of the GTOCP5 disappears when the GTOCP5 is plugged into the PC, a problem linked to the USB3 sockets of my PC, because I plug into a USB2 socket it works .

11101 - 11120 of 82250