Date   

Re: RAPAS reticle orientation

observe_m13
 

Yes, when looking down into the eyepiece the 0/24hour division on the reticle is parallel to the objective tube and points directly at the objective end.


---In ap-gto@..., <malonee72@...> wrote:

Hi Don,

Is 24h position pointing directly toward the RAPAS objective lens direction in your scope?

Thank you.
Donghun


Re: RAPAS reticle orientation

Donghun
 

Hi Don,

Is 24h position pointing directly toward the RAPAS objective lens direction in your scope?

Thank you.
Donghun


Re: Pictures of special angled pier for A-P mounts to avoid Meridian Flips

Robert Chozick
 

That is very interesting.  I had to visually recreate this with my arms to understand what you are doing.  The only failure scenario is hitting the ground.  As long as the whole setup clears the ground in any position and does not touch the vertical base holding up the mount I would think you this could go on for days turning around at any declination.  It would have to have a long arm to clear my 155 EDFS, field flattener and camera.

Robert

On Feb 22, 2014, at 7:49 PM, egroups@... wrote:

 

Robert,
Thanks for your reply.

> An A-P mount will not flip unless you tell it to do so.
Well, I'm no expert on this, but I do know that mount-control software wants to know whether it's controlling a GEM or a fork.  So my conjecture is that there are differences between merely *ignoring* the meridian (a la the A-P) and behaving as if there is *no such thing* as a meridian (a la a fork mount).  I'll admit to being unable to come up with failure scenarios, though.

My intent is to use the AP1600GTO's 90-degree declination holes to attach the mount to one of these bent piers so that the RA axis is colinear with the upper section of the pier.  I don't want to find out the hard way that this will lead me into unnatural positions such as pointing the scope toward the floor (which would not be good for my main mirror and the mirror mount).

Terry


Robert Chozick




Re: RAPAS reticle orientation

Don Anderson
 

Sounds like the set screw locking that round ring which the led reticle threads into has come loose and the ring has turned. You can simply loosen the set screw located in the body of the RAPAS at the rear just below the collar and reposition it then re-tighten the screw.
Don A


On Saturday, February 22, 2014 4:06:54 PM, "malonee72@..." wrote:
 
Hi guys,

Last night I looked through RAPAS first time in a while and I realized 24h position is not pointing straight up (not straight toward the RAPAS objective direction).
I'm pretty sure my memory is failing here but last time it seemed 24h position was pointing straight up.

I must be wrong right? 

Thank you.
Donghun



Re: Doing GTO an object on "wrong" side of pier?

Don Anderson
 

Alternately, you can also set the Meridian Delay from the Ascom driver if you want to keep your computer connected.
Don Anderson


On Saturday, February 22, 2014 2:58:28 PM, "pnagy@..." wrote:
 
Hi Terry,

If you are using ASCOM driver, try unchecking:

"Keep Mount Time Synced to PC Time (Recommended)"

This may prevent from your Meridian Delay set by hand controller from being reset by your PC.

Peter



Re: Carrying Case for AP1100

John A. Sillasen
 

Yes, please.   I'm currently contemplating a single case with lift off cover rather than hinged or dual Pelican cases.  For the weight,  the one time hoist of both pieces,  the price is less than 2 big 1600 series or 1550Ms.   I know it's a fair heft but the cabling alone may be worth having one case.   Then again my mounts are in sheds I can't reach without the mounties or at least a dog sled until some melting occurs.


John Sillasen


Re: Carrying Case for AP1100

Wayne Hixson
 

I got a case from ScopeGuard, unfortunately they are no
longer on business. 


On Feb 22, 2014, at 8:36 PM, Ross Salinger <rgsalinger@...> wrote:

 

What case did you use for your mach 1. I’ve been trying to work out what to use.

Rgrds-Ross

 

From: ap-gto@... [mailto:ap-gto@...] On Behalf Of Wayne
Sent: Saturday, February 22, 2014 5:57 PM
To: ap-gto@...
Subject: Re: [ap-gto] Carrying Case for AP1100

 

 

Thanks Paul, with my Mach1 I kept it assembled with the cabling intact. Don't want to try to horse the complete 1100 around as one piece. Will look into the Pelican cases 


On Feb 22, 2014, at 5:04 PM, Paul Lavoie <plav1959@...> wrote:

 

I use Pelican cases. I use a 1620 for the RA assembly and hand control and a 1610 for the Dec assembly, counterweight shaft, GTOCP3 and DOVELM162. I do through the mount cabling in the field, but find set up and take down as separates is not a big deal.


On Sat 2/22/14, at 16:30, <wayneh9026@...> <wayneh9026@...> wrote:

>
>
> Preparing for my 1100 to arrive in April! Wondering what other owners are using, now that ScopeGuard cases are no longer available. Probably would want a separate case for each component. For those doing thru-the-mount cabling and who do have to be portable, what do you do? Thanks! Wayne
>

i’m currently looking at these people as they can make custom size case :

http://www.casetechnology.com/

I already have a Pelican case for my 900GTO but I’m looking for a case for my AT12RC. As they can do pretty much any size with side foam up to 2” it should work for your 1100. The only thing .. it’s ont cheap.

Regards, Rodolphe

--
|        Rodolphe Pineau    RTI-Zone        |
|         http://www.rti-zone.org/          |
|   Robotics / Unix / Mac OS X / Astronomy  |



------------------------------------

To UNSUBSCRIBE, or for general information on the ap-gto list
see http://groups.yahoo.com/group/ap-gtoYahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ap-gto/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ap-gto/join
    (Yahoo! ID required)

<*> To change settings via email:
    ap-gto-digest@...
    ap-gto-fullfeatured@...

<*> To unsubscribe from this group, send an email to:
    ap-gto-unsubscribe@...

<*> Your use of Yahoo Groups is subject to:
    http://info.yahoo.com/legal/us/yahoo/utos/terms/


Re: Carrying Case for AP1100

Ross Salinger <rgsalinger@...>
 

What case did you use for your mach 1. I’ve been trying to work out what to use.

Rgrds-Ross

 

From: ap-gto@... [mailto:ap-gto@...] On Behalf Of Wayne
Sent: Saturday, February 22, 2014 5:57 PM
To: ap-gto@...
Subject: Re: [ap-gto] Carrying Case for AP1100

 

 

Thanks Paul, with my Mach1 I kept it assembled with the cabling intact. Don't want to try to horse the complete 1100 around as one piece. Will look into the Pelican cases 


On Feb 22, 2014, at 5:04 PM, Paul Lavoie <plav1959@...> wrote:

 

I use Pelican cases. I use a 1620 for the RA assembly and hand control and a 1610 for the Dec assembly, counterweight shaft, GTOCP3 and DOVELM162. I do through the mount cabling in the field, but find set up and take down as separates is not a big deal.


On Sat 2/22/14, at 16:30, <wayneh9026@...> <wayneh9026@...> wrote:

>
>
> Preparing for my 1100 to arrive in April! Wondering what other owners are using, now that ScopeGuard cases are no longer available. Probably would want a separate case for each component. For those doing thru-the-mount cabling and who do have to be portable, what do you do? Thanks! Wayne
>

i’m currently looking at these people as they can make custom size case :

http://www.casetechnology.com/

I already have a Pelican case for my 900GTO but I’m looking for a case for my AT12RC. As they can do pretty much any size with side foam up to 2” it should work for your 1100. The only thing .. it’s ont cheap.

Regards, Rodolphe

--
|        Rodolphe Pineau    RTI-Zone        |
|         http://www.rti-zone.org/          |
|   Robotics / Unix / Mac OS X / Astronomy  |



------------------------------------

To UNSUBSCRIBE, or for general information on the ap-gto list
see http://groups.yahoo.com/group/ap-gtoYahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ap-gto/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ap-gto/join
    (Yahoo! ID required)

<*> To change settings via email:
    ap-gto-digest@...
    ap-gto-fullfeatured@...

<*> To unsubscribe from this group, send an email to:
    ap-gto-unsubscribe@...

<*> Your use of Yahoo Groups is subject to:
    http://info.yahoo.com/legal/us/yahoo/utos/terms/


Re: Carrying Case for AP1100

Wayne Hixson
 

Still open to suggestions. Thanks!


On Feb 22, 2014, at 6:37 PM, <yfukunag@...> wrote:

 

I use a case with pp honeycomb sandwich panel custom-built by a local manufacturer for my 160EDF. The weight is much less than the original one and it works great for hand transport.
I will do so for the 1100GTO that will arrive in a few weeks.

Seems like you already decided with Pelican and just FYI.

Yasushi


Re: Carrying Case for AP1100

Yasushi Fukunaga
 

I use a case with pp honeycomb sandwich panel custom-built by a local manufacturer for my 160EDF. The weight is much less than the original one and it works great for hand transport.
I will do so for the 1100GTO that will arrive in a few weeks.

Seems like you already decided with Pelican and just FYI.

Yasushi


Re: Carrying Case for AP1100

Wayne Hixson
 

Definitely would like to see it - thanks!


On Feb 22, 2014, at 6:00 PM, Paul Lavoie <plav1959@...> wrote:

 

I can send pics to you if interested.

On Feb 22, 2014 8:57 PM, "Wayne" <wayneh9026@...> wrote:
 

Thanks Paul, with my Mach1 I kept it assembled with the cabling intact. Don't want to try to horse the complete 1100 around as one piece. Will look into the Pelican cases 


On Feb 22, 2014, at 5:04 PM, Paul Lavoie <plav1959@...> wrote:

 

I use Pelican cases. I use a 1620 for the RA assembly and hand control and a 1610 for the Dec assembly, counterweight shaft, GTOCP3 and DOVELM162. I do through the mount cabling in the field, but find set up and take down as separates is not a big deal.


On Sat 2/22/14, at 16:30, <wayneh9026@...> <wayneh9026@...> wrote:

>
>
> Preparing for my 1100 to arrive in April! Wondering what other owners are using, now that ScopeGuard cases are no longer available. Probably would want a separate case for each component. For those doing thru-the-mount cabling and who do have to be portable, what do you do? Thanks! Wayne
>

i’m currently looking at these people as they can make custom size case :

http://www.casetechnology.com/

I already have a Pelican case for my 900GTO but I’m looking for a case for my AT12RC. As they can do pretty much any size with side foam up to 2” it should work for your 1100. The only thing .. it’s ont cheap.

Regards, Rodolphe

--
|        Rodolphe Pineau    RTI-Zone        |
|         http://www.rti-zone.org/          |
|   Robotics / Unix / Mac OS X / Astronomy  |



------------------------------------

To UNSUBSCRIBE, or for general information on the ap-gto list
see http://groups.yahoo.com/group/ap-gtoYahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ap-gto/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ap-gto/join
    (Yahoo! ID required)

<*> To change settings via email:
    ap-gto-digest@...
    ap-gto-fullfeatured@...

<*> To unsubscribe from this group, send an email to:
    ap-gto-unsubscribe@...

<*> Your use of Yahoo Groups is subject to:
    http://info.yahoo.com/legal/us/yahoo/utos/terms/


Re: Carrying Case for AP1100

Paul Lavoie
 

I can send pics to you if interested.

On Feb 22, 2014 8:57 PM, "Wayne" <wayneh9026@...> wrote:
 

Thanks Paul, with my Mach1 I kept it assembled with the cabling intact. Don't want to try to horse the complete 1100 around as one piece. Will look into the Pelican cases 


On Feb 22, 2014, at 5:04 PM, Paul Lavoie <plav1959@...> wrote:

 

I use Pelican cases. I use a 1620 for the RA assembly and hand control and a 1610 for the Dec assembly, counterweight shaft, GTOCP3 and DOVELM162. I do through the mount cabling in the field, but find set up and take down as separates is not a big deal.


On Sat 2/22/14, at 16:30, <wayneh9026@...> <wayneh9026@...> wrote:

>
>
> Preparing for my 1100 to arrive in April! Wondering what other owners are using, now that ScopeGuard cases are no longer available. Probably would want a separate case for each component. For those doing thru-the-mount cabling and who do have to be portable, what do you do? Thanks! Wayne
>

i’m currently looking at these people as they can make custom size case :

http://www.casetechnology.com/

I already have a Pelican case for my 900GTO but I’m looking for a case for my AT12RC. As they can do pretty much any size with side foam up to 2” it should work for your 1100. The only thing .. it’s ont cheap.

Regards, Rodolphe

--
|        Rodolphe Pineau    RTI-Zone        |
|         http://www.rti-zone.org/          |
|   Robotics / Unix / Mac OS X / Astronomy  |



------------------------------------

To UNSUBSCRIBE, or for general information on the ap-gto list
see http://groups.yahoo.com/group/ap-gtoYahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ap-gto/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ap-gto/join
    (Yahoo! ID required)

<*> To change settings via email:
    ap-gto-digest@...
    ap-gto-fullfeatured@...

<*> To unsubscribe from this group, send an email to:
    ap-gto-unsubscribe@...

<*> Your use of Yahoo Groups is subject to:
    http://info.yahoo.com/legal/us/yahoo/utos/terms/


Re: Carrying Case for AP1100

Wayne Hixson
 

Thanks Paul, with my Mach1 I kept it assembled with the cabling intact. Don't want to try to horse the complete 1100 around as one piece. Will look into the Pelican cases 


On Feb 22, 2014, at 5:04 PM, Paul Lavoie <plav1959@...> wrote:

 

I use Pelican cases. I use a 1620 for the RA assembly and hand control and a 1610 for the Dec assembly, counterweight shaft, GTOCP3 and DOVELM162. I do through the mount cabling in the field, but find set up and take down as separates is not a big deal.


On Sat 2/22/14, at 16:30, <wayneh9026@...> <wayneh9026@...> wrote:

>
>
> Preparing for my 1100 to arrive in April! Wondering what other owners are using, now that ScopeGuard cases are no longer available. Probably would want a separate case for each component. For those doing thru-the-mount cabling and who do have to be portable, what do you do? Thanks! Wayne
>

i’m currently looking at these people as they can make custom size case :

http://www.casetechnology.com/

I already have a Pelican case for my 900GTO but I’m looking for a case for my AT12RC. As they can do pretty much any size with side foam up to 2” it should work for your 1100. The only thing .. it’s ont cheap.

Regards, Rodolphe

--
|        Rodolphe Pineau    RTI-Zone        |
|         http://www.rti-zone.org/          |
|   Robotics / Unix / Mac OS X / Astronomy  |



------------------------------------

To UNSUBSCRIBE, or for general information on the ap-gto list
see http://groups.yahoo.com/group/ap-gtoYahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ap-gto/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ap-gto/join
    (Yahoo! ID required)

<*> To change settings via email:
    ap-gto-digest@...
    ap-gto-fullfeatured@...

<*> To unsubscribe from this group, send an email to:
    ap-gto-unsubscribe@...

<*> Your use of Yahoo Groups is subject to:
    http://info.yahoo.com/legal/us/yahoo/utos/terms/


Re: Pictures of special angled pier for A-P mounts to avoid Meridian Flips

astrotrf2002
 

Robert,
Thanks for your reply.

> An A-P mount will not flip unless you tell it to do so.
Well, I'm no expert on this, but I do know that mount-control software wants to know whether it's controlling a GEM or a fork.  So my conjecture is that there are differences between merely *ignoring* the meridian (a la the A-P) and behaving as if there is *no such thing* as a meridian (a la a fork mount).  I'll admit to being unable to come up with failure scenarios, though.

My intent is to use the AP1600GTO's 90-degree declination holes to attach the mount to one of these bent piers so that the RA axis is colinear with the upper section of the pier.  I don't want to find out the hard way that this will lead me into unnatural positions such as pointing the scope toward the floor (which would not be good for my main mirror and the mirror mount).

Terry


Re: Carrying Case for AP1100

Paul Lavoie
 

I use Pelican cases. I use a 1620 for the RA assembly and hand control and a 1610 for the Dec assembly, counterweight shaft, GTOCP3 and DOVELM162. I do through the mount cabling in the field, but find set up and take down as separates is not a big deal.


On Sat 2/22/14, at 16:30, <wayneh9026@...> <wayneh9026@...> wrote:

>
>
> Preparing for my 1100 to arrive in April! Wondering what other owners are using, now that ScopeGuard cases are no longer available. Probably would want a separate case for each component. For those doing thru-the-mount cabling and who do have to be portable, what do you do? Thanks! Wayne
>

i’m currently looking at these people as they can make custom size case :

http://www.casetechnology.com/

I already have a Pelican case for my 900GTO but I’m looking for a case for my AT12RC. As they can do pretty much any size with side foam up to 2” it should work for your 1100. The only thing .. it’s ont cheap.

Regards, Rodolphe

--
|        Rodolphe Pineau    RTI-Zone        |
|         http://www.rti-zone.org/          |
|   Robotics / Unix / Mac OS X / Astronomy  |



------------------------------------

To UNSUBSCRIBE, or for general information on the ap-gto list
see http://groups.yahoo.com/group/ap-gtoYahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ap-gto/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ap-gto/join
    (Yahoo! ID required)

<*> To change settings via email:
    ap-gto-digest@...
    ap-gto-fullfeatured@...

<*> To unsubscribe from this group, send an email to:
    ap-gto-unsubscribe@...

<*> Your use of Yahoo Groups is subject to:
    http://info.yahoo.com/legal/us/yahoo/utos/terms/


Re: Carrying Case for AP1100

Rodolphe Pineau <pineau@...>
 

On Sat 2/22/14, at 16:30, <wayneh9026@yahoo.com> <wayneh9026@yahoo.com> wrote:



Preparing for my 1100 to arrive in April! Wondering what other owners are using, now that ScopeGuard cases are no longer available. Probably would want a separate case for each component. For those doing thru-the-mount cabling and who do have to be portable, what do you do? Thanks! Wayne
i’m currently looking at these people as they can make custom size case :

http://www.casetechnology.com/

I already have a Pelican case for my 900GTO but I’m looking for a case for my AT12RC. As they can do pretty much any size with side foam up to 2” it should work for your 1100. The only thing .. it’s ont cheap.

Regards, Rodolphe

--
| Rodolphe Pineau RTI-Zone |
| http://www.rti-zone.org/ |
| Robotics / Unix / Mac OS X / Astronomy |


Carrying Case for AP1100

Wayne Hixson
 

Preparing for my 1100 to arrive in April! Wondering what other owners are using, now that ScopeGuard cases are no longer available. Probably would want a separate case for each component. For those doing thru-the-mount cabling and who do have to be portable, what do you do? Thanks! Wayne


Re: Pictures of special angled pier for A-P mounts to avoid Meridian Flips

Robert Chozick
 

An AP mount will not flip unless you tell it to do so.  If you leave it alone it will always keep going, even to run into the pier.  Is there even a way to tell it to do an automatic flip?  I don't use the ASCOM driver since I use a Mac but just curious.  I usually only use the keypad and the only way I know how to do it with the keypad is to reenter the GOTO for the object after it goes to the other side of the meridian.

Robert

On Feb 22, 2014, at 3:31 PM, egroups@... wrote:

 

I'd really like to put my AP1600 on such a pier; I'll have to see if I can talk someone local into making one.  Is the software in the A-P mount capable of properly taking advantage of this?  It would have to be taught that, like a fork mount, there is no such thing as a meridian flip.

Terry


Robert Chozick




RAPAS reticle orientation

Donghun
 

Hi guys,

Last night I looked through RAPAS first time in a while and I realized 24h position is not pointing straight up (not straight toward the RAPAS objective direction).
I'm pretty sure my memory is failing here but last time it seemed 24h position was pointing straight up.

I must be wrong right? 

Thank you.
Donghun


Re: Doing GTO an object on "wrong" side of pier?

topboxman
 

Hi Terry,

If you are using ASCOM driver, try unchecking:

"Keep Mount Time Synced to PC Time (Recommended)"

This may prevent from your Meridian Delay set by hand controller from being reset by your PC.

Peter